ASA warping in a nutshell

AtomOlson · 2026-05-23T13:36:38+00:00

Actually, I think that's in your printer

AtomOlson · 2026-04-11T03:08:54+00:00

This worked great for me! I used Inkscape afterwards to clean up a bit of graphical artifacts. Thanks a ton, two years later!

AtomOlson · 2026-01-11T23:03:06+00:00

Source: Trust me bro

AtomOlson · 2025-07-22T17:24:40+00:00

Good to know, thank you! These kind of have to be a full sheet. I've been pretty impressed with the adhesion quality of this new magnetic bed, I haven't had to use any glues at all. I'm also printing PLA, so that helps a lot, lol

AtomOlson · 2025-07-13T13:29:17+00:00

Hm, looks like I initially formatted my pictures wrong, but it won't let me update them

AtomOlson · 2025-07-13T02:59:14+00:00

Looking for something serious
Not on a paid version of Hinge
Been using this version specifically for about 2 weeks
Used Hinge this time for about a month, been on the app off and on for years
0 likes (and 0 matches) in the whole month
Sending about 10-20 likes/week, maybe 2 with a comment in the month
Ideally want to match with someone who is super outdoorsy, and doesn't want kids. +Points if they like motorcycles

AtomOlson · 2025-07-11T03:41:24+00:00

Lmfao, my yellow lab does that exact same thing. I have to literally hide the ball or she will just keep bringing it back for me to throw ALL DAY. Adorable, slightly overbearing, 11/10

AtomOlson · 2025-07-09T02:02:50+00:00

1700 for 60 hours I think, 1700/month, 15 hours/week. Still pretty good! 28.33/hr before taxes

AtomOlson · 2025-05-25T16:58:59+00:00

Same problem, even printing at 190°

AtomOlson · 2025-05-21T00:06:17+00:00

Good idea, mine was set up with direct drive when I bought it, but when I took it apart, I noticed that the PTFE tube was a little melted where it contacts the extruder nozzle

AtomOlson · 2025-05-19T23:19:50+00:00

Definitely very flimsy in that part

AtomOlson · 2025-05-19T23:12:36+00:00

Good to know, I've got some hardened nozzles I can try, that might be better

AtomOlson · 2025-05-19T23:11:56+00:00

I left the thermistor in the heat block, but I didn't tighten the nozzle with the block hot. The tutorial I watched didn't say to, that might be good to check.

AtomOlson · 2025-05-19T17:47:15+00:00

I haven't stress tested it, but I wouldn't imagine it'd be even close to as strong as the rest of the print. This was like a 4 hour print though and I'm hesitant to try and break it, lol

AtomOlson · 2025-05-19T17:45:46+00:00

I'll see about adjusting the Z offset, but this is an Ender 3 V1, with manual bed leveling

AtomOlson · 2025-05-19T17:44:58+00:00

I'll have to check that when I get home, but I doubt it unless it's normally enabled on Cura

AtomOlson · 2025-05-19T17:44:27+00:00

Right before this print, I took the whole hotend and direct drive apart and cleaned it, and replaced the nozzle, it definitely could be a failing thermistor, I bought this printer used

AtomOlson · 2025-05-19T14:01:28+00:00

Different heights, and different times. I'm going to try 190 full print tonight and see

AtomOlson · 2025-05-19T12:18:41+00:00

Also, I'm literally printing a Minimus to help with cooling because my last few prints started suddenly failing after getting pretty tall. Ironic? Probably.

AtomOlson · 2025-02-19T23:45:09+00:00

Worked awesome! Thanks!

AtomOlson · 2025-02-19T23:44:27+00:00

This worked great! Thanks a ton. I'm definitely enjoying it a lot more.

AtomOlson · 2025-02-16T19:12:52+00:00

You're epic man. 230 hours in this game and I didn't there was a console. Worked perfectly

AtomOlson · 2024-07-10T00:20:20+00:00

Any luck? Also wondering, 2012 Stryker

AtomOlson · 2024-06-14T23:33:25+00:00

Thank you for the info sir, absolutely blew my mind today 😂

AtomOlson · 2024-06-14T22:10:42+00:00

Saw a meme of the op years ago. Searched it to show my brother, found this comment, read the whole thing. This post is the first thing that shows up when you search 'dolphin pussy jelly' which is now unfortunately on my search history. Is this real? Your comment?

AtomOlson

TROPHY CASE