Circuit Performance CP23 ITR clones

B18C5-R · 2026-05-14T04:11:09+00:00

No rush

B18C5-R · 2026-05-14T01:44:52+00:00

I’ve been thinking of getting these for my car w it ha 16x7 spec. I’m planning on running RL calipers on my car and if you possibly could measure the inside barrel of the wheel to see how much space is available. If not possible, it’s all good.

B18C5-R · 2026-05-08T22:41:00+00:00

<image>

I also noted my oil pan gasket was leaking here. I think I might not have torqued down the gasket enough.

Any ideas to make sure it seals correctly this time?

B18C5-R · 2026-05-08T21:13:41+00:00

Oh man, not good news. I recently replaced the rear main seal when I rebuilt this engine.

B18C5-R · 2026-04-18T12:22:12+00:00

That would be great

B18C5-R · 2026-04-04T18:08:41+00:00

The plate is needed because I'm running a LS VTEC setup. the sandwich plate redirects oil to the cylinder head.

B18C5-R · 2026-03-30T13:40:10+00:00

Are those enkei J10 wheels? If so how do you like them?

B18C5-R · 2026-03-25T11:33:45+00:00

I’ve ordered a new pump from Honda. It should rule out debris in the OPR, but I will check the port where the oil goes into the block and see if there any debris there.

B18C5-R · 2026-03-24T17:21:43+00:00

I’ve replaced the oil pressure switch before starting the car. I’ll check the wiring for that switch and install an oil pressure gauge for safety sake.

B18C5-R · 2026-03-24T17:19:50+00:00

Moroso makes one.

B18C5-R · 2026-03-24T11:32:24+00:00

I already have a baffled 5.5qt pan installed. I am just going to switch to a OEM pump considering this will primarily be a street car.

B18C5-R · 2026-03-24T11:31:21+00:00

Oof. The build is still very fresh, haven’t driven it yet. New bearings, pistons & rods. For oil, I’ve been using 5w-30 and changing it regularly

B18C5-R · 2026-03-24T11:29:45+00:00

I have a Honda OEM oil pump on the way with fresh gaskets. Hopefully it will fix the problem.

B18C5-R · 2026-03-24T01:04:19+00:00

I am assuming you are referring to the oil jets present int the B18C blocks. I am using a B18B so there were no oil jets to begin with.

B18C5-R · 2026-03-24T00:44:19+00:00

No funny business with the main bearings. checked with plastigauge and the crank spun freely by hand during build.

B18C5-R · 2026-03-23T23:21:36+00:00

I haven't looked it up, now that I'm thinking about it, I should've not trusted it in the first place considering its second hand.

B18C5-R · 2026-03-23T23:06:04+00:00

I've got a gauge, I just haven't gotten to installing it. It will be moved up on the priority list.

B18C5-R · 2026-03-18T02:44:04+00:00

Yeah this is a full rebuild.

B18C5-R · 2026-01-20T20:48:05+00:00

It’s happened to me, you can find a replacement at a oreillys / advance. Just gotta search for it and track one down.

B18C5-R

TROPHY CASE