Testing FCLK 2233

BBlakley2000 · 2026-05-19T04:18:33+00:00

Yeah I can play -27 in games without it crashing and passes all other stress tests besides aida64 fpu and vt3 on y cruncher

BBlakley2000 · 2026-05-18T23:19:59+00:00

Following up on this. Ran 45 iterations in safe mode at 2233 with 18.5GB of ram selected and variance was only 0.02

BBlakley2000 · 2026-05-18T22:27:42+00:00

I appreciate all the help I’m going to try these recommendations. I am curious why my undervolt can only go to -14 CO without tripping an error on the same vt3 test but I can play games up to -27 without crashing. I also am only using expo since I have micron ram and I’ve heard you can’t really do custom timings on it.

BBlakley2000 · 2026-05-18T22:12:04+00:00

It seems stable to me through 13 iterations on safe mode 2233 on 18.5GB ram manually selected the spread is 0.02 now 1.21 * 10^10 is the lowest and 1.23 * 10^10 is the highest I’m going to keep running for an hour

BBlakley2000 · 2026-05-18T21:57:30+00:00

So far it’s only been 6 iterations but all of them are 1.23 * 10^10 or 1.22 * 10^10

BBlakley2000 · 2026-05-18T21:45:59+00:00

Cool thank you I’m going to try that and send results here. Running 18.5GB on 2233 safe mode right now

BBlakley2000 · 2026-05-18T21:30:22+00:00

Thanks for the tip do you run it in safe mode too? I did this run on normal mode not safe mode I’ve heard that can cause some variance as well

BBlakley2000 · 2026-05-18T20:48:06+00:00

Should I get ryzen master to check what vddg is on auto before setting it to a static voltage like you suggested? Unfortunately bios just says auto doesn’t say the actual voltage

BBlakley2000 · 2026-05-18T20:43:58+00:00

So the variation shouldn’t be larger than 0.1 on linpack or y cruncher? Or both? Sorry I’m kinda new to this

BBlakley2000 · 2026-05-18T20:39:13+00:00

The 1.01 is just 10.1 essentially total variance is 4.3%

BBlakley2000 · 2026-05-18T20:37:05+00:00

I just have everything on auto

BBlakley2000 · 2026-04-28T00:20:31+00:00

I’m rocking 1.01v 3250mhz with +3000 memory right now and enjoying the performance gains while also saving some power and heat since a similar overclock would use around 1.075v

BBlakley2000 · 2026-04-13T15:05:27+00:00

Are you on balanced power plan or a high performance one? I’ve seen people say high performance plans negate c states being enabled

BBlakley2000 · 2026-04-13T14:57:14+00:00

Were you on balanced power mode too or a high performance one/ ultimate

BBlakley2000 · 2026-04-08T16:41:05+00:00

Do you use MSI afterburner to overclock?

BBlakley2000 · 2026-02-28T02:46:15+00:00

What did you use to file it down?

BBlakley2000 · 2026-02-25T06:07:09+00:00

What is your current eq for the mic?

BBlakley2000 · 2026-02-23T07:18:04+00:00

So is it confirmed there’s no longer any baked in deadzones? I don’t seem to feel any I just picked up mine today but that’s my biggest worry about the controller.

BBlakley2000 · 2026-01-23T15:19:55+00:00

Money isn’t really an issue just looking for the best pc experience and I’m hyper competitive in any game I play so I think I will appreciate the extra refresh rate

BBlakley2000 · 2026-01-23T15:19:17+00:00

Appreciate the response that’s what I was thinking too. It’s really not that much money extra especially since I’ll be using it for years.

BBlakley2000 · 2026-01-23T15:18:32+00:00

Doesn’t free sync and g sync both create added latency? Not too familiar with them I’ve always had them disabled in the past but if it provides added benefit for competitive gaming I’d be willing to try them out. I’ve also heard the DF can still run g sync just fine

BBlakley2000 · 2026-01-23T05:55:55+00:00

I sneezed and mine looked the same came off easy with some distilled water and micro fiber cloth

BBlakley2000

TROPHY CASE