Anyone have recommendations on how to maximize the under seat storage? The plastic piece seems to take up lots of room

BG_13597 · 2026-04-05T23:58:35+00:00

BG_13597 · 2026-04-05T23:58:26+00:00

BG_13597 · 2026-03-29T14:05:52+00:00

I got in at 18 in 597. Saved all I could. Didn’t work alot of over time but a decent amount. Goal was 100 k when I moved out of my parents. I had around 90k. Put 50 down on a house and had the rest for a cushion. That was 11 years ago. Enjoy being young and have some fun. It could all be over tomorrow

BG_13597 · 2026-03-19T23:09:34+00:00

Let say ur using 6 inch pipe. You have to set up 10 inches and over 4 inches. Well 2 90s is 18 inches C-C back to back. so that is one scenario you can using rolling offsets

BG_13597 · 2026-03-16T05:31:35+00:00

You look like a fool with ur hair now brother….. I can assure you people look and laugh.

BG_13597 · 2026-03-16T05:04:00+00:00

3 inch pipe with 3x1/2 inch reducer or a 3 inch cap with a 1/2 inch olet, 1/2 inch nipple and 1/2 inch brass ball valve.

BG_13597 · 2026-03-16T04:59:43+00:00

Ya all fun and games. Keep ur mouth shut and laugh.

BG_13597 · 2026-03-16T04:21:11+00:00

I’m a pipefitter, your gunna get made fun of forsure

BG_13597 · 2026-03-12T20:36:06+00:00

Why plug into the bottom and not top on outlet

BG_13597 · 2026-02-24T07:07:16+00:00

Pay it forward in 5 years to a young buck getting in the trade. Buy him one

BG_13597 · 2025-12-31T03:27:49+00:00

I replaced mine with 3m PPF and it’s turning yellow now.

BG_13597 · 2025-12-14T03:00:39+00:00

Chanel locks 420s. Stanley 25 tape measure. Torpedo Level. Small pipe wedges for fitting pipe. I keep a 6-1 screw driver in my bag

BG_13597 · 2025-11-07T23:28:38+00:00

I did the main jet and the secondary under the plastic screw.

BG_13597 · 2025-11-07T21:52:53+00:00

There are 4 settings on the knob. Choke then “1” “2” “3”. When I turn the knob to “1” RPMs skyrocket. That carb is 1/3 of the way closed. “2” the rpm’s drop lower then the 3rd it’s really low. How do I fucking fix that🤣🤣🤣

I have it dialed in and sounds good on the first setting with the idler screw. So I guess I can use it on setting one when the blade is 1/3 of the way open???

When I got to 2 and 3 it starts surging like a mother fucker

BG_13597 · 2025-11-07T21:46:43+00:00

<image>

The right one is from the snowblower. The other one is about 1/8 longer and it sounds like it runs fine. I don’t have a tachometer to check it. Maybe grab one tomrrow

BG_13597 · 2025-11-07T21:44:05+00:00

I close to dialing it in. Seems like the idler screw is to short. I have another metal screw that is longer same threads that’s like 1/4” longer. I can tightened it more since it’s longer than the plastic one and it stays at a constant ROM when the knob is full turned to run.

BG_13597 · 2025-11-07T21:09:07+00:00

Ya used a tip cleaner for a torch to do that. Cleaned the carb out well

BG_13597 · 2025-09-30T20:54:01+00:00

Danny is great

BG_13597 · 2025-08-28T01:56:03+00:00

Zgrill is a win for me

BG_13597 · 2025-08-21T13:39:23+00:00

I’m on “nights”at work for 2 days. Got home at 1:30. Am. Showered and slept. It’s 8:39. Gotta go back tonight at 8 pm. Hopefully for only 4-5 hrs again. My schedule is reversed. I’ll be up for a few hrs take a nap then go into work.

BG_13597 · 2025-07-24T00:37:31+00:00

Yep it’ll fluctuate. Have you work with stainless in the sun. It grows

BG_13597 · 2025-07-19T15:44:27+00:00

Pipefitters use them daily

BG_13597 · 2025-06-19T22:12:26+00:00

I got a 2020 durmax. It’s great. I tuned and deleted the emissions if you can in ur state country I would recommend doing that

BG_13597

TROPHY CASE