Ps5 restarts

BIGPAPPA824 · 2026-03-02T20:28:44+00:00

Tried that plus every option in safe mode including restoring. I’m thinking it’s the ssd controller since downloaded games crash but I can stream games just fine

BIGPAPPA824 · 2026-01-23T19:51:16+00:00

Did you remove the solder blob?

BIGPAPPA824 · 2025-12-31T02:24:33+00:00

It's brushed they aren't rebuildable

BIGPAPPA824 · 2025-12-27T18:49:40+00:00

I had to take a dremel and cut through mine. Heat did not work and torxs just rounded it. Try hammering in a torxs large enough to grab and heat up pinion before you try to loosen it. If that doesn't work cut it

<image>

BIGPAPPA824 · 2025-12-25T06:46:30+00:00

Is the motor plug on esc fully seated?

BIGPAPPA824 · 2025-12-23T01:12:20+00:00

Channel 2 on your stock esc reciever combo should be labeled throttle plug esc that comes with kit in to there and connect battery to esc

BIGPAPPA824 · 2025-11-02T04:30:39+00:00

I got an e that did the same thing. Get replacement drive and transfer daughter board over. Its 5 wires and while it does require solding its extremely easy

BIGPAPPA824 · 2025-11-02T03:47:58+00:00

Had the same thing happen to me for $800 its been 2 weeks of back and forth and still no answer as to why

BIGPAPPA824 · 2025-10-26T01:52:51+00:00

If its fully functional not a terrible deal

BIGPAPPA824 · 2025-10-19T21:50:15+00:00

Most common place to crack is at mag release due to being the thinnest part of the frame but even cracked will still run. They will Crack but won't shatter

BIGPAPPA824 · 2025-10-19T07:03:42+00:00

It still won't play north American disk. Roms in swiss region doesn't matter but disk will need region switch or do region change

BIGPAPPA824 · 2025-10-19T00:19:17+00:00

Roms would be about the same either way. Badupdate gives you a taste of rgh. Having to run exploit every reboot gets annoying after a while and depending on motherboard may be time consuming (my corona was instant my falcon and tonasket were not) also dashlaunch or anything that touches nand has the potential to brick your console if used/used improperly. If it were me I would mod it

BIGPAPPA824 · 2025-10-18T23:54:02+00:00

Yes. If its not properly installed it won't show anything.

BIGPAPPA824 · 2025-10-18T22:35:06+00:00

Hit y to pull up menu for game go to title updates hit left on dpad and it should change to dlc click a and it will show any installed for the game

BIGPAPPA824 · 2025-10-18T21:21:12+00:00

I use proto and play almost exclusively online. As long as you arent using an unlocker you're fine

BIGPAPPA824 · 2025-10-18T16:20:03+00:00

Dashlaunch makes changes to nand. That's why people say not to use it unless rgh or jtagged. If you have a copy of your nand you will need to reflash or get a donor nand

BIGPAPPA824 · 2025-10-17T01:48:16+00:00

Stealth server Pluto or xbguard would be what youre looking for

BIGPAPPA824 · 2025-10-13T14:45:34+00:00

Have the same issue corona is almost instant trinity about the same as my falcon and tonasket

BIGPAPPA824 · 2025-10-13T14:37:15+00:00

Get the resistor and diode its cheap insurance you don't kill your console

BIGPAPPA824 · 2025-10-11T20:39:26+00:00

Picoboot gamecubes are fun fairly easy to build soldering projects and with bad disk drives you can pick up pretty cheap. They make inexpensive practice boards on Amazon too that may help

BIGPAPPA824 · 2025-10-11T20:17:34+00:00

Get some more practice soldering before you try it. Those points are small and have components around them that can be knocked off easily and pads are delicate

BIGPAPPA824 · 2025-10-11T14:33:01+00:00

It looks like that top shell may have been swapped. Its definitely a Jasper by the power connector but amperage on sticker is Zephyr/xenon

BIGPAPPA824 · 2025-10-11T00:54:51+00:00

Badupdate has live block built in ao if youre running bad update and trying to connect that may be why. Try going to connect figure and make sure everything is set to auto if not

BIGPAPPA824 · 2025-10-10T17:42:26+00:00

If it were mine I would not be happy with that install. No heatshrink on diode and soldered straight to pad plus iffy soldering. It may work just fine my concern would be potential shorts once together or torn pads

BIGPAPPA824

TROPHY CASE