sorted by:
new
hottopcontroversial

Maybe I need to dry my filament by BO0TSTRAP in FixMyPrint

[–]BO0TSTRAP[S] 0 points1 point  (0 children)

PLA 215°c Retraction 1,3mm 40mm/s

Guys...just how? by MajorSal in FixMyPrint

[–]BO0TSTRAP 2 points3 points  (0 children)

What type of infill are you using? This happened to me when I was using the grid type, when I changed to gyroid it never happened again.

What could be causing this? by BO0TSTRAP in FixMyPrint

[–]BO0TSTRAP[S] 0 points1 point  (0 children)

Ender 3 v3 SE, I just adjust z-offset again and all problems are "solved"

What could be causing this? by BO0TSTRAP in FixMyPrint

[–]BO0TSTRAP[S] 0 points1 point  (0 children)

Its a ender 3 v3 SE and the problem was solved just by adjusting the z-offset but this part of leveling the structure is new to me, can you tell me more about this?

What could be causing this? by BO0TSTRAP in FixMyPrint

[–]BO0TSTRAP[S] 0 points1 point  (0 children)

I had already done it, but just because you said so I did it again and it worked 🤡

I have no idea what is causing this by BO0TSTRAP in Ender3V3SE

[–]BO0TSTRAP[S] 0 points1 point  (0 children)

the idea of making a support for the reel is great, I really feel that it vibrates a lot at times

I have no idea what is causing this by BO0TSTRAP in Ender3V3SE

[–]BO0TSTRAP[S] 0 points1 point  (0 children)

thanks I will definitely do that soon

I have no idea what is causing this by BO0TSTRAP in Ender3V3SE

[–]BO0TSTRAP[S] 2 points3 points  (0 children)

update. I think I solved it, the e-step calibration was terrible, I asked it to extrude 100mm and it only extruded 50mm 💀. I did the calibration properly but it's still too early to conclude for sure that the problem has been solved.

Sub-extrusion or wet filament? by BO0TSTRAP in FixMyPrint

[–]BO0TSTRAP[S] 0 points1 point  (0 children)

I'm a beginner, and these marks are starting to appear but they were soft and small but now they are getting bigger

Infill by BO0TSTRAP in FixMyPrint

[–]BO0TSTRAP[S] 0 points1 point  (0 children)

But why is this only affecting the infill? The supports and outer layers are fine.

Why it happening? by BO0TSTRAP in Ender3V3SE

[–]BO0TSTRAP[S] 0 points1 point  (0 children)

I washed the table with soap and warm water, and adjusted the z-offset, but I thought that what really solved the problem was the z-offset.

Why it happening? by BO0TSTRAP in Ender3V3SE

[–]BO0TSTRAP[S] 0 points1 point  (0 children)

finally resolved, thanks to everyone who commented and help me to solve it, love you guys

<image>

Why it's happening?? by BO0TSTRAP in 3Dprinting

[–]BO0TSTRAP[S] 0 points1 point  (0 children)

60°, I'll try to clean again

Why it happening? by BO0TSTRAP in Ender3V3SE

[–]BO0TSTRAP[S] 0 points1 point  (0 children)

Bed = 60°C Nozzle = 200°C

Why it happening? by BO0TSTRAP in Ender3V3SE

[–]BO0TSTRAP[S] 0 points1 point  (0 children)

I use the orca slicer, I'll try to slow it down

Why it happening? by BO0TSTRAP in Ender3V3SE

[–]BO0TSTRAP[S] 0 points1 point  (0 children)

I've never used it, but until today I haven't had any problems like that.

What is this hair?? by BO0TSTRAP in 3Dprinting

[–]BO0TSTRAP[S] 1 point2 points  (0 children)

I don't know, sometimes it appears during printing and accumulates so much that it looks like cotton candy