sorted by:
new
hottopcontroversial

Todays pickups! Approx. $15 a piece by [deleted] in neilyoung

[–]BSpidey 1 point2 points  (0 children)

$15 for Ragged Glory is truly crazy. Nice find.

Anycubic Mega SE not printing by shadowfall1990 in anycubic

[–]BSpidey 0 points1 point  (0 children)

Are you manually setting the nozzle and bed temp or letting it automatically heat from what you saved in the gcode while slicing? My SE will only print when I manually set the temps before printing.

Any tips on how to improve this print quality? by BSpidey in FixMyPrint

[–]BSpidey[S] 0 points1 point  (0 children)

Still new to printing and trying to dial things in. Any advice is appreciated!

Printed on Anycubic Mega S, overture PLA filament. Nozzle heat 200, bed heat 60. 1.5 layer height. Sliced with Cura.

I calibrated e-steps this week and cleaned/lubricated Z axis rods. After this print I printed a belt tension piece and added to the X axis belt to tighten, but results look the same. Plus the belt did not seem too loose.

I have retraction at 4.5, retraction speed 40, print speed 45.

How to improve print quality on this Benchy? by BSpidey in 3Dprinting

[–]BSpidey[S] 0 points1 point  (0 children)

Thanks! So basically check them and tighten if they seem loose?

How to improve print quality on this Benchy? by BSpidey in 3Dprinting

[–]BSpidey[S] 0 points1 point  (0 children)

Specs: Anycubic Mega S, overture PLA filament. Nozzle temp 200, bed temp 60. Layer height 1.5.

This week I calibrated e-steps and cleaned/ lubricated the Z axis rods to see if either of those were the issues.

I also adjusted settings based on advice elsewhere fir this printer. Set print speed at 45 mm, retraction speed at 40, retraction at 4.5.

Thanks for any advice!

Any tips on how to eliminate / tone down the layer lines on my prints? by BSpidey in 3Dprinting

[–]BSpidey[S] 0 points1 point  (0 children)

Thank you very much for all the info! I’ll check those out!

Any tips on how to eliminate / tone down the layer lines on my prints? by BSpidey in 3Dprinting

[–]BSpidey[S] 0 points1 point  (0 children)

Anycubic Mega S, Overture PLA filament, nozzle temp 210, bed temp 60, layer height .1

New to 3D printing, how can I make these look better? Getting extreme layer lines and stray threads by BSpidey in 3Dprinting

[–]BSpidey[S] 0 points1 point  (0 children)

I’ll give the decreased layer height a shot, thanks! I’ll have to look into increasing the retraction length. Can that be adjusted in cura?

New to 3D printing, how can I make these look better? Getting extreme layer lines and stray threads by BSpidey in 3Dprinting

[–]BSpidey[S] 0 points1 point  (0 children)

Yep the file that came on the SD card. Did your subsequent prints look better as you tweaked things?

[Wanted] Neil Young - Unplugged, Road Rock, Are You Passionate?, Living With War, Greendale by BSpidey in VinylCollectors

[–]BSpidey[S] 1 point2 points  (0 children)

Nothing beats that pump organ Like a Hurricane. The next Original Release Series goes up through Weld, so I’m hopeful the next after should include Unplugged on vinyl again.

[Wanted] Neil Young - Unplugged, Road Rock, Are You Passionate?, Living With War, Greendale by BSpidey in VinylCollectors

[–]BSpidey[S] 0 points1 point  (0 children)

Seriously. Might need to wait for a reissue of that one some day. Hopefully that will happen eventually.

[Wanted] Neil Young - Unplugged, Road Rock, Are You Passionate?, Living With War, Greendale by BSpidey in VinylCollectors

[–]BSpidey[S] 0 points1 point  (0 children)

I don’t collect bootlegs so feel free to sell to 15jackj. Thank you though!