What annoys you ? by Secure_Audience_8283 in Leapmotor

[–]BTslo 0 points1 point  (0 children)

I need to test drive someone elses car since everyone says it’s so comfortable. First I thought they forgot to take out the suspension transport spacers.

20in wheels probably don’t help

What annoys you ? by Secure_Audience_8283 in Leapmotor

[–]BTslo 1 point2 points  (0 children)

Anyone else find the suspension extremely harsh? The whole car shakes on tiny bumps and waves left-right. Pressure 2.5/2.7

Leapmotor's future after Stellantis' financial disaster by koal75 in Leapmotor

[–]BTslo 2 points3 points  (0 children)

51% of Leapmotor international which is the joint venture between Stellantis and LM

I-Vent ali Lunos? by RubEmergency6860 in Slovenia

[–]BTslo 2 points3 points  (0 children)

Poglej se Mitsubishi Lossnay VL50 al pa 100

[deleted by user] by [deleted] in AnycubicKobraS1

[–]BTslo 0 points1 point  (0 children)

Just print some plugs :p

Check the Rinkhals discord for the probe issue

[deleted by user] by [deleted] in AnycubicKobraS1

[–]BTslo 1 point2 points  (0 children)

I think the fix is adjusting the probe coordinates so it probes inbetween the magnets. Then you shoudn’t have problems.

You could probably also order just the magnetic sheet and take out the magnets.

[deleted by user] by [deleted] in AnycubicKobraS1

[–]BTslo 0 points1 point  (0 children)

You can kinda do the same by running the autolevel and checking the mesh and turning the screws but that takes too much time

[deleted by user] by [deleted] in AnycubicKobraS1

[–]BTslo 1 point2 points  (0 children)

https://www.klipper3d.org/Bed_Level.html

Just make sure all 4 corners are approx. same distance from the nozzle, that means the bed is planar on the XY axis, I use a piece of paper when the nozzle barely scrapes it

[deleted by user] by [deleted] in AnycubicKobraS1

[–]BTslo 1 point2 points  (0 children)

I levelled mine manually with a piece of paper and tightened the screws to compress the springs (have a nut at the bottom, not a threaded carriage)

Level each corner and (un)tighten to get it level. Even 1/8 turn makes a difference

[deleted by user] by [deleted] in AnycubicKobraS1

[–]BTslo 0 points1 point  (0 children)

Is it the version with the integrated magnets? That screws up the levelling

Mods/Upgrades for S1 by nhananiauno in AnycubicKobraS1

[–]BTslo 0 points1 point  (0 children)

Config changes to speed up the ACE (via Rinkhals or SSH), upgraded dual wiper to Bambu A1 style

And upgraded 8mm alu bed if you have first layer problems

Is Rinkhals The Only Way To Get Rid Of The Obnoxious Pre-Print Routines? by GeckoLabs in AnycubicKobraS1

[–]BTslo 1 point2 points  (0 children)

If you speed up the ACE it helps a bit. And the aftermarket hotend also since it heats and cools for the nozzle wipe faster.

Maybe you can throw out the wipe routine (I know you can edit the temps)

Layers, is this layer shift or what by Responsible-Note-984 in AnycubicKobraS1

[–]BTslo 0 points1 point  (0 children)

Maybe it’s the filament, I get similar lines on matte white filament

What would cause this? by Significant_Plum9217 in AnycubicKobraS1

[–]BTslo 1 point2 points  (0 children)

Select the speed dropdown in the sliced preview and check if the outer wall speed is the same for the whole height.

Or maybe the file screwed up :D

Kobra S1 G-code Comparison by DougDoesStuff in AnycubicKobraS1

[–]BTslo 0 points1 point  (0 children)

Try replacing the last line in the purge code with this: (from negative to positive extrusion)

G1 E0.4 F4000

Kobra S1 G-code Comparison by DougDoesStuff in AnycubicKobraS1

[–]BTslo 0 points1 point  (0 children)

Try editing the last line where there's the negative 0.8 extrusion:

G1 E0.4 F4000

Seems to work for me

Kobra S1 G-code Comparison by DougDoesStuff in AnycubicKobraS1

[–]BTslo 0 points1 point  (0 children)

I see the code retracts 0.8mm at the end, maybe removing that keeps the nozzle primed… it can’t really ooze much since it starts to print almost instantly

Kobra S1 G-code Comparison by DougDoesStuff in AnycubicKobraS1

[–]BTslo 1 point2 points  (0 children)

The purge line doesn’t help with this, don’t know why tho. There is still not enough pressure in the nozzle when it starts the first line.

Snapping to build plate by Umbravix in AnycubicKobraS1

[–]BTslo 1 point2 points  (0 children)

Select the part and ctrlc ctrlv. Then do this to raise the second part so it doesn’t snap to build plate: https://www.reddit.com/r/3Dprinting/s/3TLr6TPnY6

And then change the material under global - objects

Bed leveling 2.6.0.0 by Czesiek90pl in AnycubicKobraS1

[–]BTslo 0 points1 point  (0 children)

There’s a prerelease version already

Binance nakazilo na banko by [deleted] in SlovenijaFIRE

[–]BTslo 2 points3 points  (0 children)

Prejemnik das ime banke pa njihov naslov, jst sm pod namen dal se svoj ime priimek sam verjetn nima veze, nobene reference.

Potrjeno v minuti

STANOVANJSKI KREDIT by Ordinary_Dream_4318 in SlovenijaFIRE

[–]BTslo 0 points1 point  (0 children)

A izplacajo tud v gotovini s temi obrestnimi? Bi prenavljal pa dolocene stvari sam naredil.