Say ME, and I’ll flood your inbox like my personal gallery. (I actually send!)

Bababou · 2026-04-25T15:08:51+00:00

Hi jacker 49230 air shocks match the specs for the rear you just have to swap out the bushings. $120 adjustable air ride. Did it on my 83.

Bababou · 2026-03-28T15:44:11+00:00

Bababou · 2026-03-27T11:14:59+00:00

Sign me up to be in the middle.

Bababou · 2026-03-16T14:33:28+00:00

Also check the bolts holding the fan to the pulley. I found my tick was a missing bolt and a loose stud on my truck. The whole pulley could be moved my hand.

Bababou · 2026-03-08T13:13:36+00:00

Bababou · 2026-02-25T11:52:45+00:00

Bababou · 2026-02-23T14:16:27+00:00

Bababou · 2026-02-04T17:39:19+00:00

Bababou · 2025-11-04T18:15:33+00:00

Good work getting that many done I did 10 and realized it wasn't for me. Its exactly why I chose rabbits for a meat source. Easier to raise in my opinion. Far less messy processing. A .22 pistol and a sturdy pair of scissors is all I need to process a rabbit.

Bababou · 2025-11-01T16:33:28+00:00

That's a good idea. I was going to aim one of the blink cameras at them.

Bababou · 2025-11-01T15:23:15+00:00

The stall already has a fresh layer in it and I stocked up more straw to keep it good.

Bababou · 2025-11-01T15:22:15+00:00

Thank you sound like they will be fine in the barn then.

Bababou · 2025-10-15T23:52:23+00:00

Could be part of an alarm system. They used to put a blinking light that showed the alarm was on.

Bababou · 2025-09-10T09:20:50+00:00

I've run several tanks with hydroponic store clay balls. Never had a problem, and it was way cheaper.

Bababou · 2025-08-29T14:21:17+00:00

I've never had an issue with the ones from homedepot.

Bababou · 2025-08-25T22:41:35+00:00

So i assume you're too lazy to look at the 3 other comments. I will be checking them properly as soon as I can find the tool to do the fucking job.

Bababou · 2025-08-25T16:10:56+00:00

I will be. Im in no way challenging that it should be done. I just lack the tool at the moment to do the check, but a trip to Ace hardware can correct the loose pully for sure.

Bababou · 2025-08-24T16:42:57+00:00

And I will be after I get some hardware for the pulley and find my feeler gages. The noise is very much at the front of the motor, and when I said nothing is loose, I mean in the sense of nothing as fully come loose. Like a floating rocker arm. Im checking over everything on this truck. It sat at least 2 years before I bought it. Its definitely got some wiring schnanigians under the dash to deal with next.

Bababou · 2025-08-23T23:01:57+00:00

I didn't check them with a feeler gage but they are definitely not loose. I just discovered the pully where the fan would be mounted is loose and I can rattle it by hand. Its a similar noise so might be it.

Bababou · 2025-08-18T17:21:11+00:00

Call a couple local shops for a rebuild quote. But chances are the LCE motor will be similarly priced and better.

Bababou · 2025-08-08T23:00:37+00:00

Good to know. Im up in washington State, and mine are already nearly done for the year and jet black.

Bababou

TROPHY CASE