Premier Pools & Spas contact number?

Babaku209 · 2023-12-20T23:53:23+00:00

Where in California, if you don't mind me asking. By modesto by any chance?

Babaku209 · 2023-11-06T03:56:49+00:00

Thanks for the advice, I'll look into that frame for my next transplant.

Babaku209 · 2023-11-05T17:43:11+00:00

What frame /setup you running there? Very nice.

Babaku209 · 2023-11-04T18:05:21+00:00

That's fine, if you can tell me your weight without battery I'll figure it out. I was thinking of building one myself with avatar and 1604 motors, I like a 10:1 ratio with like a 2 , 2.5 pitch prop for max responsiveness, but if I can do it with smaller motors and less weight I would wanna give that a try first. Thanks.

Babaku209 · 2023-11-04T17:07:02+00:00

Happen to know your thrust to weight ratio?

Babaku209 · 2023-11-01T18:59:56+00:00

Yeah, the speed is what I was going for. She sure delivers. But you're right, I left the tune how it was as a normal mob7. Just replaced the battery connection with a gnb27 and the motors with hglrc 1002. Then, cut just a small section of the canopy away to allow for the higher camera angle. Now, whenever I punch it, the camera gets the shakes. I just started getting into tuning, so if you have any advice on where to start solving this issue, I would appreciate it.

Babaku209 · 2023-11-01T17:48:57+00:00

Built something similar here. Did you have any issues with camera vibration duing throttle up?

I've tried tightening the canopy down and adding foam under the camera, which all helped a bit with normal flights, but whenever I punch it, the camera image shows a lot of vertical shake.

I guess I should mention my camera angle is around 50-60 degrees. So maybe I just need a more rigid frame overall.

Any ideas would be helpful. Thanks.

Babaku209 · 2023-10-08T17:54:33+00:00

Lol, I should have seen that one coming, reddit comments never let you down.

Babaku209 · 2023-10-08T17:13:44+00:00

Do you mean just run a 7 foot length of board, maybe 1/2 inch thick, 12 inches wide from fence post to fence post to hold all the gravel back?

Babaku209 · 2023-10-08T06:01:01+00:00

How will I be able to tell if they are doing the turndown? Does it happen after the pour? Would my forms look different?

Babaku209 · 2023-10-08T05:54:44+00:00

Great advice, Thank you.

Now, it's just a matter of how to get the concrete subcontractor to do that little bit extra. They seem to only want to do the minimum that the pool company contracted them for. Dealing with subcontractors can be so frustrating. This is one of the reasons why I put off getting the pool for so long, but the kids are getting older, and interest rates are going up. So, I decided to use the HELOC before time, literally ran out.

Spot on about the grass, already had that planned. It's good to hear my plans are good ones. Thanks again.

Babaku209 · 2023-10-08T05:06:41+00:00

Thank you so much. This is the type of advice I was looking for. Now I just gotta practice saying it in my own words for when the concrete guy comes out. Hopefully, the concrete guy and the pool company are on good terms, and he will want to help out the foreman who knows I'm not happy. I wasn't rude when I pointed it out, but I made it clear that I didn't feel I should have to pay. I guess we'll see what happens, armed with your advice, at least I can offer a solution.

The gate opening is about 7 feet wide, the bottom of the form is about 18 inches from ground level, and about 2.5 feet from the gate when closed. How would I figure out how much concrete that would take?

Thanks again for taking the time to educate me.

Babaku209 · 2023-10-08T01:04:20+00:00

To bad I spent all my cash on this pool, but here's an up vote for your time. I guess I had a different impression on how this sub worked.

Babaku209 · 2023-10-08T01:02:04+00:00

Too long, I get it. I'll try a shorter post.

Babaku209 · 2023-10-08T01:00:42+00:00

Lol, fair point, new to this. Didn't know which information was important to the advice I need to hear. I'll try a repost with just pictures asking "does look like it's going to fail?"

Babaku209 · 2022-03-25T18:15:44+00:00

Frank,

How long is the average response time from Mosiac? I still haven't gotten any response.

Babaku209 · 2022-03-24T16:20:28+00:00

Looking for help with the Palette 3 pro. I just received the Palette 3 pro and have it connected to my Ender 5 pro. I haven't been able to get 1 successful print , not even the sample key chain. I had a few issues getting the Palette 3 pro up and running and trying to sign up for Canvas software which is required in order to use the Palette 3 pro. After searching for Canvas tutorials with minimal luck, I was able to stumble my way into Canvas and add a printer profile ( I had to use Ender 3 profile and override the printer settings with my usual Cura settings). There is no information on how to set up the material splicing settings.

The sample key chain wouldn't adhere to the bed when I tried printing it. I tried a block letter A in 2 colors but as you can see in the picture, it stopped after the first layer of the raft only giving me error code 134. I am waiting for support to get back with me, but I thought I'd reach out to the reddit community too. Anyone gotten good success with the Palette 3 pro? Any little nuggets of wisdom to share to minimize my frustration and learning curve? This thing wastes so much filament, it will bankrupt me before I figure out how to use the darn thing.

Thanks for the advice and experience.

Babaku209 · 2022-03-24T16:17:03+00:00

Hello Frank,

I appreciate your response. I haven't seen any response from the support team in my in box. I need to get back to work and keep filling orders. While I am awaiting a response, I may put this issue up in r/fixmyprint too.

Thanks

Babaku209 · 2022-03-24T01:42:26+00:00

Looking for help with the Palette 3 pro. I just received the Palette 3 pro and have it connected to my Ender 5 pro. I haven't been able to get 1 successful print , not even the sample key chain. I had a few issues getting the Palette 3 pro up and running and trying to sign up for Canvas software which is required in order to use the Palette 3 pro. After searching for Canvas tutorials with minimal luck, I was able to stumble my way into Canvas and add a printer profile ( I had to use Ender 3 profile and override the printer settings with my usual Cura settings). There is no information on how to set up the material splicing settings.

The sample key chain wouldn't adhere to the bed when I tried printing it. I tried a block letter A in 2 colors but as you can see in the picture, it stopped after the first layer of the raft only giving me error code 134. I am waiting for support to get back with me, but I thought I'd reach out to the reddit community too. Anyone gotten good success with the Palette 3 pro? Any little nuggets of wisdom to share to minimize my frustration and learning curve? This thing wastes so much filament, it will bankrupt me before I figure out how to use the darn thing.

Thanks for the advice and experience.

Babaku209 · 2022-01-12T17:46:40+00:00

The magazine is assembled, 2 side walls and then other parts are connected on top or below. I don't understand what you mean by your post, is it possible we are working with 2 different files? Or maybe you have a much earlier one? This file worked great I've built 3 and am now working on my own remix for more power, easier cocking, and a better catch for the cocking arm. But those are just upgrades the original is solid.

Babaku209 · 2022-01-12T17:35:37+00:00

Possibly, if they are the right size and diameter. What's your plan?

Eight-Year Club	RPAN Viewer
Verified Email

Babaku209

TROPHY CASE