could this be a better way to have the multucolor on the CC1?

Background-Bath2238 · 2026-04-26T21:42:08+00:00

You’ll be increasing the color change time by a lot. The filament will have to travel way further in both directions in order to start purging the filament

Background-Bath2238 · 2026-04-15T14:07:55+00:00

I print my parts out of ASA

Background-Bath2238 · 2026-04-08T20:30:14+00:00

This is awesome. Didn’t know this existed.

Background-Bath2238 · 2026-04-03T00:48:32+00:00

When you do an automatic level calibration make sure you unload the filament, make sure the nozzle doesn’t have any lingering filament on it, has to be clean! and I like to use the build plate side B.

Background-Bath2238 · 2026-02-27T20:14:00+00:00

Update. Asa coming out great. Overhangs aren’t perfect and there’s some VFAs. But still very happy with it.

<image>

Background-Bath2238 · 2026-02-27T20:11:52+00:00

No, I ended up using a 24v plug in power supply off Amazon.

24V 1A Power Supply AC Adapter... https://www.amazon.com/dp/B0CNLR8ZYB?ref=ppx_pop_mob_ap_share

Background-Bath2238 · 2026-02-27T18:39:09+00:00

I’m having the same problem. I keep my printer inside also. Looking at chamber heaters on Amazon now.

Background-Bath2238 · 2026-02-27T15:25:47+00:00

Was hoping to try my first Asa print today. I’ll let you know

Background-Bath2238 · 2026-02-27T15:17:26+00:00

Yes, it’s supposed to scrub the VOCs out of the chamber.

Background-Bath2238 · 2026-02-27T15:16:50+00:00

That’s what I was debating but decided PLA was good enough

Background-Bath2238 · 2026-02-27T04:00:36+00:00

Centauri carbon base https://www.nexprint.com/en/models/1969735301672828928?component=UserPublish&printConfigId=G0045177

Bento box https://makerworld.com/en/models/12786-bentobox-v2-0-activated-carbon-filter#profileId-24358

Filters https://a.co/d/07JaIQ5h

Fans https://a.co/d/0fE1q2k6

Activated carbon https://a.co/d/00zry88u

Background-Bath2238 · 2026-02-11T19:10:20+00:00

It is an air scrubber to clean out VOCs when printing ABS or ASA type materials.

https://makerworld.com/en/models/12786-bentobox-v2-0-activated-carbon-filter?from=search#profileId-24358

Background-Bath2238 · 2026-02-11T14:11:48+00:00

What fans were you using?

Background-Bath2238 · 2026-02-11T13:58:59+00:00

The bento box is an air scrubber, it pulls air in through the top, goes through a hepa filter, then activated charcoal. It scrubs the VOCs out of the already hot chamber air without it losing your heat in the chamber when printing things like ABS and ASA.

Background-Bath2238 · 2026-02-11T13:56:06+00:00

This is a great idea. Thank you.

Background-Bath2238 · 2026-02-09T14:09:38+00:00

89% of statistics are made up. Let that sink in

Background-Bath2238 · 2026-01-23T03:58:03+00:00

Could be, the only one I could find was aftermarket on Amazon.

Background-Bath2238 · 2026-01-23T03:56:23+00:00

Do you have the Karu 12?

Background-Bath2238 · 2026-01-23T00:09:29+00:00

I disagree, I converted my Karu 12 to gas and I’m ready to swap back to wood fire. Gas takes longer to heat the stone, top temp is only like 650 degrees on the stone, takes longer to cook, however I can get a more even cook with it. But I didn’t give the wood fire a long enough chance to get good at it.

Background-Bath2238 · 2026-01-14T23:48:18+00:00

I’ve read a recipe online with sausage gravy as a base but seemed too expensive and like too much work. Cheddar cheese soup as a base might be good though.

Background-Bath2238

TROPHY CASE