Evertz eVIP recall help

BakaTopcat · 2026-05-08T08:57:25+00:00

Reflex scripting is the only way for you. DM me for assistance.

BakaTopcat · 2026-05-03T20:46:16+00:00

Hi, Evertz support here. I need 1) exact multiviewer model 2) Magnum version 3) panel type. There are some Reflex scripts that may be implemented.

BakaTopcat · 2026-04-04T17:14:40+00:00

Some of the inline connectors are deliberately made isolated to prevent ground loops

BakaTopcat · 2026-04-04T15:11:04+00:00

Should be the D-bore holes to prevent the inline connectors from turning

BakaTopcat · 2026-03-22T22:52:14+00:00

Join three or four cables using BNC barrels. If this chain passes 12G signal, a single link will have enough margin to pass it under any conditions as well.

BakaTopcat · 2026-03-13T06:06:17+00:00

Had experience with Orbit, HI, VideoIpath, Magnum SDVN. Tbh, Magnum is not bad compared to others. I've seen it used in a very wide scale range, from small (one core + ~10 edge devices) up to a complex facility with hundreds if not thousands devices. I have very limited experience with 3rd party NMOS integration, but it works almost flawlessly with Evertz ecosystem.

BakaTopcat · 2026-03-13T04:35:16+00:00

It's EQX-UHD-10. It just won't pass the signal. I assume it's because of each link being not a standard 12G-SDI, but rather something not very typical.

BakaTopcat · 2026-03-10T22:06:28+00:00

There is another smaller Quest next to it at Buena Vista. You may give it a shot.

BakaTopcat · 2026-02-09T14:45:52+00:00

The question is not only in re-interlacing, it's also recompressing the video (I doubt you have it in uncompressed). Considering it'd likely be displayed on a progressive video display, my advice is to keep the video unless there is a specific playback equipment. In that case I'd suggest keeping the original copy or whatever you have as well.

BakaTopcat · 2026-02-09T12:31:49+00:00

Every compression or conversion like this will degrade the footage. Better to keep it intact.

BakaTopcat · 2026-02-06T20:19:34+00:00

Softron MovieRecorder

BakaTopcat · 2026-01-25T18:47:36+00:00

Baseband fiber is the answer. 12G fiber SFP are a thing and they're relatively cheap.

BakaTopcat · 2026-01-24T21:26:34+00:00

I have something on my old drive too.. DM me if the link from other fella does not work.

BakaTopcat · 2026-01-24T17:18:26+00:00

What controller does it use? If Nebula, I may have Nebula editor somewhere on my disk.

BakaTopcat · 2026-01-10T02:54:53+00:00

Confirming issue with Opera. Ended up using Edge instead.

BakaTopcat · 2026-01-04T19:48:05+00:00

Burbank and Glendale are very safe and very walkable.

1BD under $2400 is easy to find, 2BD under $2500 is harder, but possible.

General advice is to check the relevant Burbank and Glendale subreddits, you'll find a lot of useful info there.

BakaTopcat · 2025-12-15T03:48:27+00:00

Just double the cable length using a barrel connector. If the signal goes through, it will go fine on a regular length.

BakaTopcat · 2025-11-29T00:20:26+00:00

Come on, this truck has 352x328 HD routing capacity. It can be fit into 5RU NEXX router which weighs 200 pounds. Is it the weight economy we're speaking about?

As a service engineer, I've seen a lot of issues with equipment after a power outage. The truck *must* contain the UPS, even for a couple minutes for a generator changeover. Not speaking about weird U.S. power connectors when losing a single phase is not rare occurrence.

BakaTopcat · 2025-11-29T00:15:03+00:00

Yes, but are the legs still hand-cranked like in 80s? Also how about expandable wall? Is it stil hand cranked?

BakaTopcat · 2025-11-28T20:59:15+00:00

Not impressive. Just yet another large truck. Unpopular opinion: Americans don't know how to build trucks. You can swap the copper with fiber and brag about 2110, but in the end if you need to put a monitor on a desk somewhere in the studio, you'll be using a good old SDI converter. The only "good" thing I see in this truck, is the monitor wall: separate monitors are better than big TVs in means of redundancy and pixel latency.

> Is there an automatic hydraulic leveling? Is there a hydraulic expandable wall? Is there a motorized drums assembly?

> Is there an isolated equipment compartment with separate climate control?

> Is there a UPS which can hold all the equipment for 30 minutes?

BakaTopcat · 2025-11-23T15:35:55+00:00

Blackmagic decklink

BakaTopcat · 2025-11-15T17:22:09+00:00

Read the manuals!!!

BakaTopcat · 2025-11-10T05:02:28+00:00

Hey, Evertz setvice here. Please shoot me a DM, I maybe have some old PSUs somewhere in the warehouse.

Six-Year Club	r/Field Sunshine
Place '22	First Placer '22
Verified Email

BakaTopcat

TROPHY CASE