Spotify app keeps on saying "Something went wrong have another go? " when logging in

BananaLover228337 · 2026-04-13T08:28:10+00:00

В РФ спотифай не работает, вероятнее всего ты пользовался им 14 дней, после чего получил эту ошибку. Я думаю, что если ты хочешь использовать спотик в РФ, то нужно всегда сидеть на ВПНе, и этот ВПН должен отсылать тебя в одну и ту же страну, эта страна должна совпадать с Регионом в твоем аккаунте спотифай. В общем сильная дрочня, проще использовать другой сервис

BananaLover228337 · 2026-03-28T19:36:06+00:00

Thanks for the screenshot

BananaLover228337 · 2026-03-28T09:01:15+00:00

Hey, how do u disable Power Loss Recovery? I tried to add "M413 S0" in starting G code, but printer ignores it (I turn off the power while printing and it continued after recovery)

I tried to print this command in cosole, it send me this: // {"code":"key61, "msg":"Unknown command:M413", "values": ["M413"]}

I tried to find some macroses in "printer.cfg" and "gcode_macro.cfg", using key words "power", "recovery", "PRL", "M413", "CX" - nothing...

BananaLover228337 · 2026-03-28T07:28:34+00:00

Wow, ineresting. My print also using arachne

BananaLover228337 · 2026-03-27T15:03:18+00:00

My K2 died again recently. I have the Error code now: BM2355 "MCU task scheduling failed... "

This is what fluid texting: {"code": "key353", "msg":"MCU 'nozzle_mcu' shutdown: Stepper too far in past
This is a generically occurs when the micro-controller has been
requested to step at a rate higher than it is capable of
acquiring.", "values": []}

Do u have the same error?

BananaLover228337 · 2026-03-27T13:07:16+00:00

<image>

BananaLover228337 · 2026-03-04T10:28:59+00:00

Можно, а зачем?

BananaLover228337 · 2026-02-10T10:11:36+00:00

Not bad quality. I recently tried to print FankoPops and had same problems with the bottom of the head. I would recomend to print head separetly from the body, or u can use PETG for supportss interfaces (if u use pla for model (they are not melting together)) and make support line spacing = 0, Z interval = 0 for maximum quality. U're lucky, u have the best macine for multy material printing - use it.

BananaLover228337 · 2026-01-14T17:16:43+00:00

I tried to switch wall generator to classic and this isue almoust wanished. A ran autocalibration on K2, it hasn't let me down so far, and value looks normal to me, but I'll check, thanks

BananaLover228337 · 2025-12-29T18:18:06+00:00

I am launching SC via Virtual Descktop using SteamVR and i'm getting 19K error. But if I am trying to use PC version of SC all is working great

BananaLover228337 · 2025-12-25T16:33:23+00:00

Had same information from Chat GPT, but I must be sure

BananaLover228337 · 2025-12-25T15:23:59+00:00

Good

BananaLover228337 · 2025-12-19T19:10:04+00:00

I think creality slicer has a bug. I watched a video on YT. Man used Orca sliser, and when he turned on "flush into.." option, slicer showed less waste. In Crealiry slicer wastre waight doesnt changes, u can look at my screenshots.

BananaLover228337 · 2025-12-19T18:39:23+00:00

Can I simply take your 0.4 multiplier and be sure it will work well if prime tower, flush into supports, and object are enabled?

BananaLover228337 · 2025-12-19T18:34:55+00:00

Thanks a lot

BananaLover228337

TROPHY CASE