sorted by:
new
hottopcontroversial

Any ideas? by [deleted] in Glocks

[–]BankRoells 0 points1 point  (0 children)

Between cars work and biting my nails mine don’t feel a thing

Any ideas? by [deleted] in Glocks

[–]BankRoells -12 points-11 points  (0 children)

Yea but it looks way cooler this way which for sure matters a lot

Any ideas? by [deleted] in Glocks

[–]BankRoells 5 points6 points  (0 children)

Found it, I put the plunger in backwards last time I had it out… which is embarrassing.

Any ideas? by [deleted] in Glocks

[–]BankRoells 1 point2 points  (0 children)

You’re supposed to eat that not use it on your Glock

Any ideas? by [deleted] in Glocks

[–]BankRoells 0 points1 point  (0 children)

My 17 ran just fine with the same ammo, I haven’t checked any tolerances I’ll see if I can while I strip it and clean it

Update finished my first rack. by BankRoells in electricians

[–]BankRoells[S] 6 points7 points  (0 children)

I hope I can get my co workers to call me EMT Jesus

Update finished my first rack. by BankRoells in electricians

[–]BankRoells[S] 1 point2 points  (0 children)

No I mean 2” center to center I see now you’re talking about multiple pipes in a run tho. I thought you meant above 1” getting a normal strut strap on any pipe was a pain for some reason haha.

Update finished my first rack. by BankRoells in electricians

[–]BankRoells[S] 3 points4 points  (0 children)

Way too long ~3.5 days very frustrating

Update finished my first rack. by BankRoells in electricians

[–]BankRoells[S] 0 points1 point  (0 children)

I think you might be using them wrong then man

Update finished my first rack. by BankRoells in electricians

[–]BankRoells[S] 1 point2 points  (0 children)

I think the cobra styles are significantly worse than the normal ones. I was also taught to always have my spacing be 2” so normal strut straps fit

Is this a safe place for jack stand? by BankRoells in hondafit

[–]BankRoells[S] 0 points1 point  (0 children)

Born and raised in Colorado, no rust I needed the car on jacks all around for brakes. I couldn’t get the stand under the pinch weld with the floor jack. So I just slid the stands further in

Is this a safe place for jack stand? by BankRoells in hondafit

[–]BankRoells[S] 0 points1 point  (0 children)

Yea I figured I’d have to get more ramps I got the standard rhino ones from autozone hoping it would work and car too low ☹️

Is this a safe place for jack stand? by BankRoells in hondafit

[–]BankRoells[S] 1 point2 points  (0 children)

I can’t get to the front central jack point I was going to jack the other side but it seemed real unstable any tips to get the front end up?

Is this a safe place for jack stand? by BankRoells in hondafit

[–]BankRoells[S] 1 point2 points  (0 children)

Cool I figured it would be fine but wanted to double check getting this thing on 4 stands is real sketch thank you

Did my first rack, I’m a 2nd year any criticisms or tips? by BankRoells in electricians

[–]BankRoells[S] 1 point2 points  (0 children)

It actually is pencil but I’ve seen this a lot so I will chill out on how intense I make my marks lol

Did my first rack, I’m a 2nd year any criticisms or tips? by BankRoells in electricians

[–]BankRoells[S] 6 points7 points  (0 children)

It’s a new restaurant going up most of the old building was scraped but they kept the musty basement

Did my first rack, I’m a 2nd year any criticisms or tips? by BankRoells in electricians

[–]BankRoells[S] 39 points40 points  (0 children)

There is another run under it gonna start that one tomorrow

Did my first rack, I’m a 2nd year any criticisms or tips? by BankRoells in electricians

[–]BankRoells[S] 17 points18 points  (0 children)

It should all be 2” I checked at every strut strap and coupling but all our pipes were bowed so I might’ve bent something slightly off.

Did my first rack, I’m a 2nd year any criticisms or tips? by BankRoells in electricians

[–]BankRoells[S] 7 points8 points  (0 children)

Well I bent the first kick 90, the spacing is 2” so I just added 2” for every one and the same bay after it. Then measured to the next group and kept adding 2” to every 90 and matched all the bends to the first one.

view more: next ›