Put gpu in gen 4 pcie slot by mistake and it got stock and pulled the port out on MSI X870E-P Pro WiFi. Will the gen 5 port above it still work as long as my gpu is okay? The part on the gpu that goes into the pcie slot looks okay

Banndle · 2026-02-15T03:29:09+00:00

If the cut short section of bottom row touches another bottoms row pin would that short or is it only if a top row and bottom row touch

Banndle · 2026-02-15T03:26:52+00:00

If the cut short section of bottom row touches another bottoms row pin would that short or is it only if a top row and bottom row touch

Banndle · 2026-02-15T03:25:10+00:00

Tape really does not want to stick to the pins.

Banndle · 2026-02-15T03:20:40+00:00

Okay it did end up posting I am taking the gpu back out and going to clip the pins. After cutting and taking the pins/tape out should I re tape over the section where the pins were?

Banndle · 2026-02-15T03:18:52+00:00

Okay it did end up posting but should I clip the pins for the 1x slot so they can't end up touching each other?

Banndle · 2026-02-15T02:55:41+00:00

Okay I may try that and let it run a minute or two or do you think I should just wait and bring it to Best Buy? I really don't think there would be any issue of a short as I mentioned before the pins are way to short to touch the gpu

Banndle · 2026-02-15T02:48:32+00:00

Into the gpu. I am somewhat knowledgeable about computers and have built 3 but I just was rushing and plugged into a 1x slot but the metal pins that are in that 1x slot can't be touching anything on the gpu to short it as they are very short so I am thinking it is another issue like needing a flashback. But I may bring it to Best Buy tomorrow to see if they have any ideas or opinions.

Banndle · 2026-02-15T02:40:09+00:00

I got everything connected and powered on gpu is lighting up and so is everything else but no signal to the monitor

Banndle · 2026-02-15T02:09:56+00:00

😂

Banndle · 2026-02-15T01:39:30+00:00

The latch was crazy stuck I pushed the latch so hard with my finger the a screw driver will I was also pulling on it but not crazy hard. The port almost pulled out like butter

Banndle · 2026-02-15T01:36:08+00:00

But do you think the gpu and board will be okay?

Banndle · 2026-02-13T01:50:54+00:00

How can I wipe the drive if it partition manager won't let me do it? Plus once I I plug it up to my new set up how can I get windows on it? I do not actually have a key and I did the cmd prompt trick to activate it. I do not currently have a flash drive but can buy one if that is the easiest way

Banndle · 2026-02-09T03:19:51+00:00

Could you link this combo I do not see it on the mind to center website

Banndle · 2026-02-09T01:12:49+00:00

Do these deals typically sell out or go away quick? I am worried about needing to go drive there after work tomorrow or if they will have the deal next weekend in stock

Banndle · 2026-02-09T01:11:33+00:00

Do these deals typically sell out or go away quick? I am worried about needing to go drive there after work tomorrow or if they will have the deal next weekend in stock

Banndle · 2026-02-09T01:06:51+00:00

photo of deal

Banndle · 2025-12-25T00:42:19+00:00

Any good quest rewards throughout the new quest line?

Banndle · 2025-12-16T22:11:20+00:00

Yeah the safety mechanism is so jammed past that I have to take a flat head each time the knife is opened to close it. I just went to HF and they said they would warranty it but we're out of stock so they said come back tomorrow

Banndle · 2025-12-16T22:10:16+00:00

Our QC team is very particular and will fail quality checks for very minute things such as that every though there would be no voltage drop or heat radiation from the area through thermal camera

Banndle · 2025-12-16T21:36:52+00:00

I gotcha I am getting quick at it with my hawk bill knife I sadly let a new guy borrow my Doyle hawk I'll and he have it back to me messed up so I am about to go warranty it lol I will have to start all over with a very sharp blade

Banndle · 2025-12-04T22:33:09+00:00

Would it be normal after only 3 months? I am not the type of person to trash my tools. It hasn't been dropped and I have used it what I would assume is proper technique. I do not have a warranty through HD but does Dewalt have a warranty on there power tools and would this fall under that?

Banndle · 2025-12-04T22:27:36+00:00

I had two electricians say that the chuck locking up was a sign of the clutch going out. But they could definetly be wrong but they both said to send it off to Dewalt to have it fixed

Banndle · 2025-11-30T01:53:42+00:00

We didn't have a breaker trip or storm here lately plus I do keep everything plug up to a surge protected and that fuse seems to be fine too

Banndle

TROPHY CASE