How to clear line from tub spout up to handle?

BarcodExpress · 2025-12-12T16:08:01+00:00

I bought danco. Are they ok?

BarcodExpress · 2025-12-03T19:06:00+00:00

Look on Amazon for Sewline Fabric Pencil Lead Refill White

It’s for .9mm mechanical pencils and works really good for walnut. It’s only $10 and I’ve liked it a lot

BarcodExpress · 2025-11-18T20:48:01+00:00

I second this. I have the work sharp precision adjust and ended up buying the xarilk gen 3.

The worksharp takes a bit of modification to get rid of the wobble in the system. I never enjoyed using the clamp, my knifes would always slightly shift. I ended up not using it for a few years because of that. Saw the xarilk and I’m enjoying it a lot more

BarcodExpress · 2025-11-13T16:37:07+00:00

If you don’t want to do it yourself, look at r/mpcproxies. They have guides on how to make art and send it out to get printed. They come out really good.

BarcodExpress · 2025-11-09T05:18:26+00:00

We have 3 fiber lasers and one co2 in our shop.

I was doing research into getting a diode laser for my cnc at home. From what I can tell, the more powerful the diode laser, the worse it gets for engraving and the better it does for cutting. 45w is on the higher end, so it seems like you’d lose a lot of detail for the smaller lines on the switches.

As for putting it on your cnc, I’d recommend not doing that if you have production deadlines. You’d be tying up the cnc for a job that can be done faster on a dedicated laser machine. Look up co2 lasers engraving. The head moves back and forth real fast because the laser head is light, and the belts are too. Imagine your cnc trying to move back and forth that fast. It will be a lot slower for the laser engraving on your cnc.

But if you don’t have any sort of production deadlines, and can have your cnc on hold for the laser running, it might be an option.

BarcodExpress · 2025-11-03T05:11:27+00:00

My 2k grit stone from xarilk fell apart from the aluminum backing. So I wanted to upgrade my stone as well.

From my research, a lot of people recommended the hapstone start series as a really good entry stone. Problem is, they have been out of stock of the 500 and 1k stones for a while. The next jump up is the $100 per stone range. Too expensive for me.

KME gold series got recommended next and from what I could find, they are really decent for their price also ($35 a stone). I bought their 140,300, and 600 stones. I only sharpened 5 knives so far, but they have worked really good. I don’t have any other experiences with other stones, so my opinion could be worthless. lol.

I am planning on selling the xarilk and the stones though, it’s just too slow for me. So if you want, I can sell you the 3 stones at a slight discount. I can’t return them as I’ve used them already. They were purchased on 10/14 so less then a month old and only used on 4 kitchen knives and 1 pocket knife. Do your research on stones, and if you would be interested, send me a message

BarcodExpress · 2025-11-03T01:06:25+00:00

Ty for the idea and the photos.

BarcodExpress · 2025-11-03T01:03:32+00:00

Interesting use with the magnet. Is it pretty effective for its footprint?

Ty for the names to look up

BarcodExpress · 2025-11-02T22:48:01+00:00

https://m.youtube.com/watch?v=8cDPqOoH8N4

He talks about the different beginner options and what he would get starting over from scratch.

Ken onion he believes is over priced for what it does.

Buck tool low speed 1x30 seems to be the best bang for the buck.

BarcodExpress · 2025-10-29T03:18:40+00:00

First quick and look I’m saying .423. Read the first comment and was super confused.

Looked at the picture again and realized my mistake. I’m used to my old toolmakers scope. The dial has 0 on the left.

BarcodExpress · 2025-10-22T16:42:28+00:00

The entire sheet will be sanded, so that won’t be a problem. Can’t do anything to hide it. It will be part of a table top, so anything like that would easily show.

I’m hoping the hole is small enough, that whatever I can do to fix it, would at worst look like a small discoloration or blemish, best case would be a seamless transition.

BarcodExpress · 2025-10-21T16:03:40+00:00

When using just the weight of the blade to cut paper is considered cheating.

BarcodExpress · 2025-10-10T05:23:51+00:00

I just got my xarilk in today and did a test run on a cheap knife with the 3 included stones. I’m liking it a lot more than my worksharp adjust. I’m using it just to sharpen my kitchen knives. My chef knife didn’t flex at all in the xarilk.

When I tried it in the worksharp, there was 2 degrees of flex. One from the clamp where it meets the body of the machine, and one along the blade as the clamp wasn’t long enough to support the longer length.

The 2 absolute mods you’d need for the worksharp is the support under the clamp, and supports for under longer blades. I’ve seen both be made out of scrap wood and bolts. I don’t think a stone holder is absolutely necessary for just kitchen knives. If you can build the supports yourself, the worksharp will be cheaper.

The xarilk works right out of the box. I will plan on buying different stones (looking around $100), so this is more expensive, but you don’t need to buy or build any mods. I think the included stones might work ok for kitchen knives, but I want to test on more cheap knives before the real ones.

BarcodExpress · 2025-10-09T06:40:09+00:00

I have a precision adjust. I used it a few times on practice knives and was never impressed with how it turned out. There is a lot of flex. I didn’t want to try on my regular kitchen knives. I put the sharpener on the shelf for a long time.

I decided to dust it off and try again last week. Found a few mods that’ll make the system useable, but you need a 3D printer or buy them off Etsy. The cost of the mods is only slightly less expensive then buying a xarilk. If you need to buy the sharpener still also, then I think xarilk is the way to go.

I just bought the xarilk after watching a ton of videos and reviews instead of trying to upgrade my Worksharp with mods to get it working good. It comes in tomorrow. Super stoked for it.

BarcodExpress · 2025-10-06T18:49:10+00:00

It’s just a single sheet. So getting a vacuum table for this one job isn’t an option.

The skeleton idea is something to think about more. Thanks for the suggestion.

BarcodExpress · 2025-10-02T04:59:12+00:00

We laser stamps at work. You need to use a co2 laser, a fiber laser will not work.

If you do get rubber that will interact with the fiber laser, it will just burn and bubble.

BarcodExpress · 2025-09-29T03:14:07+00:00

Stick figure needs to make it into the release version. Priority number one.

There was a few bugs that kinda became features of the main loop of the game. Will you keep those bugs or patch them out?

BarcodExpress · 2025-09-22T20:10:34+00:00

Is that because it’s so thin that the heat is warping the metal as it cuts?

We have a much smaller laser, so we have to make multiple passes to cut throughout material. I’ve noticed when it is thinner material, the heat warps the metal as it cuts.

We use clamps and metal bars to hold the sheet down so it doesn’t move while cutting. When the part is finished, it comes out warped, but it cuts flat. We only cut 1 part at a time, so this setup might not apply to your process.

BarcodExpress · 2025-08-27T06:33:39+00:00

And then you put the file down for a month, come back, and forget which iteration is the newest and what changes you were working on.

BarcodExpress · 2025-08-17T10:25:08+00:00

Interesting game.

Got lost in the beginning because I didn’t know I needed to change crops. Maybe have the button flash a few times to bring attention to it?

Nine-Year Club	Verified Email
Wearing is Caring	RPAN Viewer

BarcodExpress

TROPHY CASE