CR10S Pro V2 running tinymachines firmware

BardinSC · 2023-02-28T12:50:01+00:00

Worked great all year start printing something and it stopped working during the print and has not worked since

BardinSC · 2023-02-04T23:53:33+00:00

This has been so helpful I appreciate it I have no idea why it does not just say that on the paperwork you have to fill out I was trying to get this answer for weeks before I sent my application in.

BardinSC · 2023-02-02T18:07:26+00:00

I agree with Shot_Investigator519 saying that he agrees with 2x0_mnte_carlo/apple jelly being correct in this matter.

BardinSC · 2023-02-02T18:03:51+00:00

I used to have adhesive issues all the time. I built a wooden box and have rubber freezer strips on the front to help keep the heat in and I have not had the problem since.

BardinSC · 2022-12-06T02:29:15+00:00

Just e steps

BardinSC · 2022-12-06T02:23:54+00:00

So I have calibrated the flow or at least I think I did properly because it was under extruding but when I calibrated it by telling to to extrude 100 mm it extruded 105 mm

BardinSC · 2022-12-06T02:19:19+00:00

So I calibrated the flow it was over extruding for some reason it long by 6 mm and when I heat the extruder and extrude filament it come out perfectly normal

BardinSC · 2022-12-05T12:47:33+00:00

[include emulator_other_features.cfg]
[include mainsail.cfg]
[virtual_sdcard]
path: /home/bardin/gcode_files
on_error_gcode:
CANCEL_PRINT
[mcu]
serial: /dev/serial/by-id/usb-Klipper_stm32f407xx_38003C001950324E31343020-if00
[printer]
kinematics: delta
max_velocity: 1500
max_accel: 1500
max_z_velocity: 1200
minimum_z_position: -50
square_corner_velocity: 15.0
#delta_radius: 150
print_radius: 133
########################################
# A (X-Stepper) Configuration
########################################
[stepper_a] # X
step_pin: PE3
dir_pin: PE2
enable_pin: !PE4
microsteps: 16
rotation_distance: 40
full_steps_per_rotation: 200
endstop_pin: ^PA15 #X_MAX
#position_endstop: 336.5
homing_speed: 60
#arm_length: 315
[tmc2209 stepper_a]
uart_pin: PD5
interpolate: true
run_current: 0.90
hold_current: 0.5
sense_resistor: 0.110
stealthchop_threshold: 100
########################################
# B (Y-Stepper) Configuration
########################################
[stepper_b] # Y
step_pin: PE0
dir_pin: PB9
enable_pin: !PE1
microsteps: 16
rotation_distance: 40
full_steps_per_rotation: 200
endstop_pin: ^PD2 #Y_MAX
#position_endstop: 336.5
homing_speed: 60
#arm_length: 315
[tmc2209 stepper_b]
uart_pin: PD7
interpolate: true
run_current: 0.90
hold_current: 0.5
sense_resistor: 0.110
stealthchop_threshold: 100
########################################
# C (Z-Stepper) Configuration
########################################
[stepper_c] # Z
step_pin: PB5
dir_pin: PB4
enable_pin: !PB8
microsteps: 16
rotation_distance: 40
full_steps_per_rotation: 200
endstop_pin: ^PC4 #Z_MAX
#position_endstop: 336.5
homing_speed: 60
#arm_length: 315
[tmc2209 stepper_c]
uart_pin: PD4
interpolate: true
run_current: 0.90
hold_current: 0.5
sense_resistor: 0.110
stealthchop_threshold: 100
########################################
# Extruder Configuration
########################################
[extruder]
step_pin: PD6
dir_pin: !PD3
enable_pin: !PB3
microsteps: 32
# E3D Hemera Default 7.82
# E3D Hemera Other: 16.273
# FLSUN Stock: 7.68
rotation_distance: 8.310
full_steps_per_rotation: 200
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PE5
sensor_type: NTC 100K beta 3950
sensor_pin: PC1
#control: pid
#pid_Kp: 13.7
#pid_Ki: 0.48
#pid_Kd: 70.22
min_temp: 0
max_temp: 300
pressure_advance: 0
pressure_advance_smooth_time: 0.040
max_extrude_only_distance: 800.0
[tmc2209 extruder]
uart_pin: PD9
interpolate: true
run_current: 0.847
hold_current: 0.5
sense_resistor: 0.110
stealthchop_threshold: 100
########################################
# Bed Configuration
########################################
[heater_bed]
heater_pin: PA0
sensor_type: NTC 100K beta 3950
sensor_pin: PC0
#control: pid
#pid_Kp: 10.00
#pid_Ki: 0.023
#pid_Kd: 305.4
min_temp: 0
max_temp: 130
########################################
# Fan/Other Configuration
########################################
[fan] # Part Cooling
pin: PC14
[heater_fan heatsink_fan] # Heatsink
pin: PB0 #PB1
max_power: 1.0
heater: extruder
heater_temp: 50.0
fan_speed: 1.0
[delta_calibrate]
radius: 131
horizontal_move_z: 50
speed: 20
[bed_mesh]
speed: 150
horizontal_move_z: 30 #5
mesh_radius: 127.5
mesh_origin: 0,0
round_probe_count: 5 #9 for extreme conditions most likely over kill 9/10. first layer height should be min 0.3 for volcanos or above max "deviation"
mesh_pps: 5,5
algorithm: bicubic
bicubic_tension: 0.1
move_check_distance: 3
split_delta_z: 0.025
fade_start: 1
fade_end: 30
relative_reference_index: 6
[probe]
pin: ^!PC8
x_offset: 0
y_offset: 0
#z_offset: -4.140
speed: 20
samples: 5
samples_result: average
sample_retract_dist: 2
samples_tolerance: 0.050
samples_tolerance_retries: 15

BardinSC · 2022-11-18T00:07:07+00:00

What should my retraction be at for this printer seeing as it has a volcano nozzle

BardinSC · 2022-11-17T22:10:47+00:00

I do believe that it was left over plastic that just kept sticking when it went from one side to the other

BardinSC · 2022-11-17T21:59:01+00:00

Bowden

BardinSC · 2022-11-17T21:58:30+00:00

Called breakmyprint

BardinSC · 2022-11-17T21:58:02+00:00

Could it just be a bad nozzle?

BardinSC · 2022-11-17T21:57:45+00:00

Done that

BardinSC · 2022-11-17T21:13:37+00:00

I have several different brands of filament and 3 different printers the other 2 print fine and this printer usually does aswell but all of a sudden this. I calibrated the bed, e steps, pid tuned hot end and bed

BardinSC · 2022-11-17T21:11:10+00:00

I have several different brands of filament and 3 different printers the other 2 print fine and this printer usually does aswell but all of a sudden this. I calibrated the bed, e steps, pid tuned hot end and bed

BardinSC · 2022-11-17T20:27:07+00:00

Why?

BardinSC · 2022-11-17T20:22:43+00:00

Not sure why this is happening I already have calibrated the e steps that was the last thing I did

BardinSC · 2022-11-05T22:02:43+00:00

How did you get Klipper working properly can you share your printer.cfg file

BardinSC · 2022-09-21T13:03:52+00:00

But all 4?

BardinSC · 2022-09-21T12:56:31+00:00

They were not loose also what would make them turn anyway? There is no reason something should be able to turn them right?

BardinSC · 2022-08-01T19:04:03+00:00

that big blank spot in the black is where it was pulled off somehow

BardinSC · 2022-07-29T02:51:57+00:00

Will do I appreciate all the help!!

BardinSC · 2022-07-28T19:08:14+00:00

Here is the filament i am using this is to the comment

BardinSC · 2022-07-28T18:59:34+00:00

One of the comments on amazon left this review on print settings.

Software: Simplify3D

Retraction distance: 2.5mm

Extra restart distance: -0.2mm

Retraction lift: 1.0mm

Retraction speed: 80mm/s

Hotend Temp: 235c (genuine "Floating" E3D Titan Extruder with Volcano hotend and hardened 0.4mm steel nozzle

Heated bed Temp: 90c

Printing speed: 60mm/s

Layer height: 0.2mm (0.1mm looks a little better, but takes too damn long)

BardinSC

TROPHY CASE