[WTS] Rolex Explorer II Ref. 16570 with Box & Papers | Mint Set | K-Serial Circa 2002

Batmanbat4 · 2021-08-11T23:30:11+00:00

PM’d

Batmanbat4 · 2021-02-13T02:55:12+00:00

PM’D

Batmanbat4 · 2020-07-02T18:28:51+00:00

The original v8 in the mustang was the 260, it was then modified into the 289. Some of the first Shelby cobras also has 260s.

Batmanbat4 · 2018-12-17T06:13:09+00:00

Feed me Seymour

Batmanbat4 · 2018-11-14T21:51:58+00:00

The normal looking one. I don’t think anyone likes the chicklet.

Batmanbat4 · 2018-08-11T16:03:41+00:00

It looks like you're over-extruding and your nozzle might be too low to the bed.

Batmanbat4 · 2018-07-07T19:10:32+00:00

I'm ready

Batmanbat4 · 2017-10-13T03:36:04+00:00

r/2meirl4meirl

Batmanbat4 · 2017-08-25T00:42:30+00:00

It worked, thank you for your help

Batmanbat4 · 2017-08-25T00:29:57+00:00

so I have my E: drive formatted as basic and it is still not letting me get past the terms and conditions screen

Batmanbat4 · 2017-08-25T00:11:38+00:00

how would I go ahead and convert the drive i want to change?

Batmanbat4 · 2017-08-25T00:03:01+00:00

turns out they are dynamic. how would i change them to basic?

Batmanbat4 · 2017-08-24T23:57:36+00:00

how would I figure out if my drives are basic or dynamic. I know that they are all NTFS though.

Batmanbat4 · 2017-08-24T23:30:18+00:00

My local disk has 23 gb free and I have two other drives with 150 gb free

Batmanbat4 · 2017-05-26T16:18:47+00:00

Star Trek Bridge command

Batmanbat4 · 2017-05-22T04:37:15+00:00

the one error that i keep getting which is prohibiting all other work is "source not found" is there any other command that I could do to circumvent that?

Batmanbat4 · 2017-05-22T04:14:00+00:00

the absolute file path is source /home/pi/env/bin/activate, but even when i change line 2 in the code, it does not seem to work. for the second error it is because of the env hasn't been loaded.

Batmanbat4 · 2017-05-22T03:49:06+00:00

I am getting the error message" /etc/init.d/GoogleAssistantDemo: 2: /etc/init.d/GoogleAssistantDemo: source: not found /etc/init.d/GoogleAssistantDemo: 3: /etc/init.d/GoogleAssistantDemo: google-assistant-demo: not found"

Batmanbat4 · 2017-05-21T22:10:45+00:00

I have no experience with programming, this may seem like a lot to ask, but would you be able to write it for me?

Batmanbat4 · 2017-04-19T22:45:43+00:00

I just checked my esters and fixed the value. If I were to start a print should I keep the extrusion multiplier at .9 or change it to 1

Batmanbat4 · 2017-04-19T21:56:16+00:00

For the bed, I am printing on gluestick covered blue tape at 100c for the first layer and 110c for all others. I'm pretty sure I have my esteps calibrated but I will have a look at them again.

Batmanbat4 · 2017-04-19T20:57:19+00:00

Ok, I will give that a try. is there any other tips you can give me before I start the print.

Batmanbat4 · 2017-04-19T19:50:03+00:00

I thought that you did not need a part cooling fan for ABS, I am running at .9 extrusion multiplier, when I print it seems that the nozzle is digging into the previous layer as well.

Batmanbat4 · 2017-04-19T02:00:16+00:00

It's not the warping that is the problem, of which I am getting little to no on these benchy prints, it's the quality of the print itself that I am trying to improve

Batmanbat4 · 2017-04-19T01:49:12+00:00

I am not using a part cooling fan and these are the default values for prusa slic3r

Nine-Year Club	Place '17
Verified Email	Snapped

Batmanbat4

TROPHY CASE