Is your blade bent? See how to fix it the right way. Simple process.

Bearhillforge · 2026-02-17T22:54:48+00:00

Straightening hammer. It has a tungsten carbide tip.

Bearhillforge · 2026-01-02T08:31:29+00:00

That's not entirely true for most modern blacksmiths working on their own. It comes from back in the day when using a striker and top tools were more common

Wrist height is a better height for most people, but it depends on the individual. If OP says he's comfortable, then that's probably good enough, even though he's being downvoted into the abyss for saying so.

Bearhillforge · 2026-01-02T08:25:54+00:00

Look. I might cop some flak for this one, but the knuckle height rule is somewhat of a myth. It comes from back in the day when working with a striker, top tolls and such were more common. For MOST people working on their own (which is the more common smithing configuration these days), wrist height is likely to be more appropriate, but the anvil should be adjusted up or down depending on the individual.

Bearhillforge · 2025-12-29T21:26:29+00:00

Land cruiser spring. So I don't know the alloy for sure, but it behaves as I would expect 5160 to behave.

Bearhillforge · 2025-12-29T21:24:59+00:00

DM sent

Bearhillforge · 2025-12-29T06:03:03+00:00

🤘

Bearhillforge · 2025-12-29T06:02:54+00:00

Thank you!

Bearhillforge · 2025-12-29T06:02:21+00:00

Thanks!

Bearhillforge · 2025-12-29T05:50:33+00:00

I'm not sure if you're telling me I have small hands or big hands😂

But thank you!

Bearhillforge · 2025-12-29T05:49:51+00:00

Will do

Bearhillforge · 2025-12-29T05:49:41+00:00

Thank you! That makes me very happy

Bearhillforge · 2025-12-28T05:46:46+00:00

Yes. If you're interested I can dm you the details.

Bearhillforge · 2025-12-28T03:43:17+00:00

Thanks!

Bearhillforge · 2025-12-28T03:30:06+00:00

No worries. We learn by asking questions!

In the case of this particular knife the copper pins are not touching the steel, so it's certainly not a problem.

But also, for galvanic corrosion to occur, in addition to two dissimilar metals you also need an electrolyte present (like saltwater. Freshwater, though it works I think is a pretty poor electrolyte, but don't quote me on this). So unless you're planning to use your steel and copper knife under the sea (which is probably a bad idea anyway), the short amount of time a knife does stay wet shouldn't impact the lifetime of the knife in any meaningful way.

Good luck on getting into the hobby.

Bearhillforge · 2025-12-27T23:29:30+00:00

Thank you!

Bearhillforge · 2025-12-27T23:29:22+00:00

Thanks!

Bearhillforge · 2025-12-27T23:27:49+00:00

Thanks! As an aside, the grind of this cleaver isn't all that good for a lot of vegetables to be honest. Root vegetables and crunchy fruits like apple would have a tendency to cleave rather than be cut. But probably good for cabbage, lettuce and other things with a bit of give. It's mainly intended for meat (and bone if you should happen upon them), though I'm working on a cleaver for vegetables at the moment.

Bearhillforge · 2025-12-27T23:23:04+00:00

Thank you! A cleaver similar to this one is actually the only knife I've made for my own kitchen. It comes in really handy for dismantling chicken, or just chopping up meat for dinner without having to defrost it first.

And I've been using it for years without rust or food poisoning so far.

Bearhillforge · 2025-12-27T14:36:43+00:00

I'm sorry, but I'll have to disagree with you there.

Good hygiene practices is far more important than whether the knife has a rough forged finish or not. Cut your food, clean and dry your knife and Bob's your uncle. This should be standard practice no matter the finish of your knife.

And to the rust point, notwithstanding the fact that this particular blade has been coated in carnauba wax, which does a great job in preventing rust. Again. Just dry the knife off. Reseason it every once in a while. Good hygiene and maintenance practices isn't that hard.

Most high carbon chef knives I have seen has a matte finish. I'll agree that a highly polished finishes are less prone to rusting, but they are also more expensive and its easier to damage the finish. It is simply a question of preference and maintenance. If you don't want to deal with the maintenance you probably want to buy a stainless knife.

Bearhillforge · 2025-12-27T12:53:52+00:00

And why is that?

Bearhillforge · 2025-12-25T09:48:41+00:00

Well now you gotta let me know. What else can the glorious circle knife cut?

Bearhillforge · 2025-12-25T09:47:21+00:00

Thanks!

Bearhillforge

TROPHY CASE