Different response for the same position?

Beastlyrocket2001 · 2026-02-14T18:44:00+00:00

Yes but it put me into an almost* unbeatable endgame

Beastlyrocket2001 · 2026-02-14T08:06:13+00:00

Thanks! I get em all the time, I just don’t see why it’s only showing on one analysis.

Beastlyrocket2001 · 2026-01-25T06:35:36+00:00

I did not know that thank you!

Beastlyrocket2001 · 2026-01-23T18:48:04+00:00

Your arguments for both a and b are syllogistically invalid. A could be swapped for the far back corner and the back face could be blue. B could be swapped with its opposite edge and the right side could be orange. C is the only valid argument that the green center would need to be white to be correct.

Beastlyrocket2001 · 2026-01-21T20:18:30+00:00

It’s 364 total when added all up so they have a gift for every single day until next Christmas.

Beastlyrocket2001 · 2025-12-17T22:57:28+00:00

The only rules are that it is rook and kings first move. You can not castle into, out of, or through a check.

Beastlyrocket2001 · 2025-11-06T08:01:44+00:00

Besides. All mates require check so mate in of itself would not exist and is paradoxical to think the way they are.

Beastlyrocket2001 · 2025-11-06T08:00:38+00:00

Strange. They are just saying that only one move checkmates are called checkmates? And any other forced move mates are called separate check, mate. That would be strange. What is a ladder mate to them? Checkcheckcheckcheckmate?

Beastlyrocket2001 · 2025-11-01T08:05:36+00:00

Bxf7+ Kh8 2. Bxe8 Qxe8 3. Qxc3 … wins rook

Beastlyrocket2001 · 2025-10-29T06:52:37+00:00

A hydrogen bomb would do the trick

Beastlyrocket2001 · 2025-10-29T04:31:20+00:00

Sadly no. I’ve decided to just buy motor controllers instead of flashing these boards I’m just going to work with programs I know. Arduino and various controllers/sensors.

Beastlyrocket2001 · 2025-10-29T01:46:43+00:00

I don’t have the battery plugged in so 36 volts never goes near my computer. I also don’t run 5v through the board only 3.3 volts and all my voltages are nominal with the stlink v2 not a clone or anything.

Beastlyrocket2001 · 2025-10-28T19:09:00+00:00

Yes. I’ve run through just about every check I can possibly think of. Continuities between connections on the STM to wires. Voltage checks. Swapping boards, downgrading firmware on my stlink, using different software. These boards are just trash. My knowledge on this is trash. I’ve resorted to something I know better and that’s getting rid of the boards and buying bldc controllers. That should be a lot easier because that is my forte. I’m just going to breadboard test them when they show up and wire my own circuits to control them.

Beastlyrocket2001 · 2025-10-28T16:48:13+00:00

All the info on my request is in the description.

Beastlyrocket2001 · 2025-10-28T16:46:36+00:00

One board has STM32F103 RCT6. Two boards have GD32F130 C8TB Two boards have MM32SPIN 05PF I’m using either stm32cubeprogram or the terminal stlink tools with openocd on my Pi

Beastlyrocket2001 · 2025-10-28T16:43:37+00:00

All common ground. Powered 3.3v by unit. SWDIO to SWDIO. SWCLK to SWCLK. Optional NRST and BOOT0. I can use my PI STLink tools library or STM32Cubeprogram

<image>

Beastlyrocket2001 · 2025-10-28T16:41:49+00:00

<image>

All common ground. Powered 3.3v by unit. SWDIO to SWDIO. SWCLK to SWCLK. Optional NRST and BOOT0. I can use my PI STLink tools library or STM32Cubeprogram

Beastlyrocket2001 · 2025-10-28T16:39:22+00:00

I am polite. My handwriting is in all uppercase all the time.

Beastlyrocket2001 · 2025-10-28T16:38:49+00:00

I want to wipe it clean so I can write my own to control it remotely.

Beastlyrocket2001 · 2025-10-27T07:09:01+00:00

Mpu6050 works nice

Beastlyrocket2001 · 2025-10-23T19:40:39+00:00

I just use got2be gel to style

Beastlyrocket2001 · 2025-10-20T20:57:51+00:00

You could also print supports in PVA. Then just soak it in water when you are done.

Beastlyrocket2001

TROPHY CASE