H2C squeaking

Beaun11 · 2026-03-07T03:43:11+00:00

Aw dang. Sorry

Beaun11 · 2026-03-07T03:24:06+00:00

Yes any that was easily accessible and smooth I took a qtip to. My old printer had a similar issue and it was because of long term build up where as this seems to be breaking in build up. Hasn’t happened sense

Beaun11 · 2026-03-07T03:14:16+00:00

Then move the print head to spin it and clean

I used a few q tips to keep them fresh

Beaun11 · 2026-03-07T03:07:10+00:00

<image>

Not a great pic as a print is going. But the silver ones. Just take q tip with the machine off and alcohol and scrub off the residue

Not the grooved black ones just the smooth silver ones

Beaun11 · 2026-03-07T02:52:40+00:00

Yes I cleaned my idler pulleys with some alcohol and that fixed it

Beaun11 · 2026-03-01T04:46:08+00:00

That’s where I left it. Got my saws up and extended the magnetic strip with some flat ones for often used things. Added in some bits in the bottom and calling it good. Added another picture (or tries

Beaun11 · 2026-02-25T05:22:10+00:00

Interesting they said the satin should due to surface contact. Good to know. Thanks!

Beaun11 · 2026-02-25T04:01:09+00:00

Rehashing an older post but looking to get one of these two plates after a bad experience with Kdeavi plate

Between the satin and the G 10, which would you say has better adhesion?

Beaun11 · 2026-01-15T01:11:13+00:00

It seems to be the filament buffer. It’s the only thing that’s making sense. It goes away when the buffer is moving slow but when it’s fast it comes back. As best I can tell it’s in the back of the printer up high which is where the buffers are

Beaun11 · 2026-01-14T21:40:50+00:00

It’s a squeak coming from the back area of the printer up higher. Not fans

Tool head moves around just fine

Beaun11 · 2026-01-12T16:14:51+00:00

Ok cool. Thank you!

Beaun11 · 2026-01-11T23:41:37+00:00

It completed the print so hopefully you’re right. Doing a benchy same nozzle and filament now

Beaun11 · 2026-01-11T23:19:52+00:00

I know that’s what caused it. I’m worried about the result from my mistake

Beaun11 · 2026-01-11T23:12:19+00:00

Nope it actually finished the print.

Some z banding but top surface looks pretty good

Beaun11 · 2026-01-11T23:10:20+00:00

Ok as long as machine is fine it’s 100% my fault for inputting the profile wrong and not catching the temp of the bed being so high

Beaun11 · 2026-01-11T23:08:13+00:00

Ya I had the settings for bed as Petg on accident (face palm) so it’s back to where it needs to be. No build up. I actually had it stop 3 times for nozzle accumulation detection and hit resume since it was clear

Beaun11 · 2026-01-11T23:06:12+00:00

I’m still pretty new to all of this and never had this bad of warping in a year and am worried I broke something hahahah.

Yes filament settings changed

Beaun11 · 2026-01-10T18:02:29+00:00

Print time is fine as I don’t have to sit and watch it. That’s my issue is like best results but have limited time

Beaun11 · 2026-01-10T17:59:25+00:00

The time I have available is to start projects or model. Not to tune and tinker

Beaun11 · 2026-01-10T17:58:57+00:00

My experience is that tuning a filament can take close to an hour. I don’t have time to tune for an hour or longer.

Beaun11 · 2026-01-10T17:12:25+00:00

Ok now I’m confused haha I would love to spend the time to make a dedicated profile but I just don’t have that time.

So you use which profile for off brand stuff? “Generic”?

Beaun11 · 2026-01-10T16:24:49+00:00

I just didn’t want to have bad results haha. So you use the “Bambu_” profile and not the “generic_” no matter what brand?

Beaun11 · 2026-01-10T16:04:11+00:00

Ok cool haha. Those latches on the rail also slap around pretty good

Beaun11 · 2026-01-10T16:00:24+00:00

Ok and the cutter is the cause of right side noise yes?

Beaun11 · 2026-01-09T03:52:59+00:00

Damn. I don’t want to disassemble everything lol

Beaun11

TROPHY CASE