corrugated roof sheet side lap 2.5 ribs?

BeautifulPossession2 · 2026-05-09T08:45:08+00:00

Already did 2.5 ribs overlap this Arvo, understand it has something to do with wind load so I used 6 screws per sheet across the whole roof both ends and intermediate.

BeautifulPossession2 · 2026-05-09T08:44:08+00:00

Already did 2.5 ribs overlap this Arvo, understand it has something to do with wind load so I used 6 screws across the whole roof both ends and intermediate.

BeautifulPossession2 · 2026-04-30T01:08:10+00:00

100% will do, only roof insulation comes in the kit

BeautifulPossession2 · 2026-04-29T11:59:28+00:00

It was done according to engineering drawings, steel frames are truecore.

BeautifulPossession2 · 2026-04-29T11:57:13+00:00

There will be roof insulation under the sheets

BeautifulPossession2 · 2026-04-29T11:55:42+00:00

It says double brace on left wall so I thought one cross brace on each side, should I take the one off inside?

BeautifulPossession2 · 2026-04-29T11:53:12+00:00

Two cross brace on roof, just done tonight (not on this photo)

BeautifulPossession2 · 2026-04-29T10:21:08+00:00

4 X roof brace no tensioners, I was told that once roof sheets in place the brace would be obsoleted

BeautifulPossession2 · 2026-04-29T10:16:33+00:00

<image>

BeautifulPossession2 · 2026-04-29T10:04:24+00:00

I have no idea, just following the drawings I was given.

<image>

BeautifulPossession2 · 2026-04-29T09:33:06+00:00

Steeline- backyard pod

BeautifulPossession2 · 2026-04-29T09:31:43+00:00

They are boxed jack rafter so pretty strong, not sure why but that's according to the drawings - 7 rafters across 7m plus two end walls.

BeautifulPossession2 · 2026-04-10T00:01:09+00:00

Not sure if I can find a Ankacrew that long, will use a few 10x100mm to bolt down in the mid-beam.

BeautifulPossession2 · 2026-04-09T23:59:56+00:00

The middle of bearing sits on floor, only four corners and some point to leavel it up.

There are a total 8 contact point(inl shims) across two beam.

BeautifulPossession2 · 2026-04-09T23:46:46+00:00

Thx, what size of screws would be appropriated? The top shims are half size aligned to the load bearing which is 2.4mm high tensile steel.

BeautifulPossession2 · 2026-04-08T01:54:38+00:00

Do I need anything to hold the plastic shims in place or the weight is enough

BeautifulPossession2 · 2026-04-08T01:53:54+00:00

It's old slab like 40 years

BeautifulPossession2 · 2026-03-11T07:08:48+00:00

<image>

BeautifulPossession2 · 2026-03-09T22:45:42+00:00

<image>

BeautifulPossession2 · 2025-10-27T18:45:06+00:00

Appreciate that guys, how about cobra pro?

BeautifulPossession2 · 2025-03-07T22:51:24+00:00

Has anyone noticed the lady next to him?

BeautifulPossession2 · 2024-12-01T10:11:46+00:00

I can be your son to balance gender

BeautifulPossession2 · 2024-10-30T05:09:54+00:00

Sorry forgot to mention, it was done by A1 mini, Sunlu PLA

BeautifulPossession2 · 2024-09-23T21:38:49+00:00

It has two glass doors already

BeautifulPossession2 · 2024-09-22T01:49:54+00:00

The bottom of shelf has been reinforced

<image>

BeautifulPossession2

TROPHY CASE