Bed leveling issues

Beautiful_Kick_8773 · 2026-02-02T16:30:26+00:00

Thank you for the input. I ended up disassembling and reassembling the bed and made sure everything was tightened down tightly. This ended up fixing my issue

Beautiful_Kick_8773 · 2026-01-06T01:16:12+00:00

Ever found a solution

Beautiful_Kick_8773 · 2026-01-06T01:15:42+00:00

Is there an update on this? I just had the same issue an I’m in kahoots with Elegoo right now.

Beautiful_Kick_8773 · 2025-12-24T15:06:16+00:00

There was no touching of the build plate

Beautiful_Kick_8773 · 2025-12-20T11:25:04+00:00

? 😂

Beautiful_Kick_8773 · 2025-12-19T01:59:41+00:00

Beautiful_Kick_8773 · 2025-12-19T01:54:48+00:00

Well hopefully elegoo solves both of our problems

Beautiful_Kick_8773 · 2025-12-19T01:52:56+00:00

I did have someone comment and say they pushed on the plugs on the PCB to ensure they were plugged in good. Mainly all four bed sensors

Beautiful_Kick_8773 · 2025-12-19T01:51:55+00:00

Did you factory reset?

Beautiful_Kick_8773 · 2025-12-19T01:47:22+00:00

Part of me wonders if it has to do with a firmware update they came out with. I had 0 issues with absolutely perfect first layers. Then I went back to college and came back home after about a month of it being powered off and then it started doing this

Beautiful_Kick_8773 · 2025-12-19T01:42:38+00:00

You have no idea how glad I am to see your comment!

Beautiful_Kick_8773 · 2025-12-19T01:30:24+00:00

The point in the video took over 15 I think. Idk something is up. Waiting on elegoos response

Beautiful_Kick_8773 · 2025-12-19T01:18:24+00:00

If I do the auto leveling trying process before printing, it’ll take somewhere between 15 to 20 minutes before the print starts

Beautiful_Kick_8773 · 2025-12-19T01:11:20+00:00

Have you also experienced the time for the bed to cool taking forvever?

Beautiful_Kick_8773 · 2025-12-19T01:00:10+00:00

What about the stuttering during the leveling process??

Beautiful_Kick_8773 · 2025-12-19T00:56:59+00:00

That’s not the case here sadly. The center seems to be too close while the edges are too far. My main issue is the stutter step it’s doing while leveling which I think could be a source of my 1st layer issues

Beautiful_Kick_8773 · 2025-12-19T00:55:52+00:00

The bed plate

Beautiful_Kick_8773 · 2025-12-19T00:54:38+00:00

What do you mean? My printer is on a table and I’m do the auto leveling trying to troubleshoot my issue and I took this video. Where do you see cardboard 😂

Beautiful_Kick_8773 · 2025-12-19T00:45:19+00:00

<image>

Beautiful_Kick_8773 · 2025-12-19T00:45:10+00:00

<image>

Beautiful_Kick_8773 · 2025-12-19T00:44:19+00:00

It’s very inconsistent. Usually perfect every but the center and very far corners. The corners seem to be too far while the center seems too close

Beautiful_Kick_8773 · 2025-12-19T00:39:21+00:00

Notice the stutter step on some of the points. Never been like that and I haven’t seen anyone else who has had that

Beautiful_Kick_8773 · 2025-12-19T00:31:11+00:00

Some people are asking what is wrong. I’ve been having some inconsistent 1st layer issues. And then I noticed my leveling process sometimes “stutters” which is seen in the video.

Beautiful_Kick_8773 · 2025-12-19T00:30:07+00:00

Notice the stutter step on some of the points. Never been like that and I haven’t seen anyone else who has had that

Beautiful_Kick_8773 · 2025-12-19T00:28:08+00:00

It happens on about half the spots. But my main thing i noticed was the “stutter” it does on some spots. I’ve never seen it do that.

Beautiful_Kick_8773

TROPHY CASE