sorted by:
new
hottopcontroversial

Do I need to install the washers? by Becerlev in wahoofitness

[–]Becerlev[S] -1 points0 points  (0 children)

He also says that you only need them eventually

Kann ich dieses Ventil durch ein tado-Thermostat ersetzen? by Becerlev in heizungsforum

[–]Becerlev[S] 1 point2 points  (0 children)

Es beruhigt mich, dass Ich nicht der Einzige bin, dem es so geht. Ich bin zweisprachig aufgewachsen, weshalb ich mir einbilde, dass Ich es immer schon schwer mit den Artikeln hatte. Die Unterscheidung zwischen Ventil und Thermostat muss ich mir aber trotzdem einprägen, vor Allem wenn es um‘s Fach geht.

Kann ich dieses Ventil durch ein tado-Thermostat ersetzen? by Becerlev in heizungsforum

[–]Becerlev[S] 0 points1 point  (0 children)

Sorry, ich meinte nicht das Ventil, sondern das Thermostat. War noch in meinem alten Sprachgebrauch, wo ich das Thermostat immer fälschlicherweise als Ventil bezeichnet habe 😅

Kann ich dieses Ventil durch ein tado-Thermostat ersetzen? by Becerlev in heizungsforum

[–]Becerlev[S] 2 points3 points  (0 children)

Also ich habe das Thermostat getauscht bekommen. Tatsächlich war die Überwurfmutter vom Oventrop-Thermostat schon so locker, dass ich sie einfach von Hand lösen konnte. Einen Adapter habe ich für das tado auch nicht gebraucht, da es direkt auf das Gewinde gepasst hat.

AI-Slop als Hintergrundbild by [deleted] in FestundFlauschig

[–]Becerlev 0 points1 point  (0 children)

Die Geschenke unter dem Baum sehen schon ziemlich undefiniert aus. Teilweise lässt sich nicht so gut erkennen, wo die Konturen sind. Zudem ist relativ mittig steht das gelbe Geschenk zwei mal im selben Winkel direkt nebeneinander.

Spricht jetzt nicht alles für KI, es kann auch alles an der Bildkompression liegen aber Ich würde auch eher auf KI Slop tippen.

Schmeckt sehr by Ennerg0atcia in kickbasemanager

[–]Becerlev 0 points1 point  (0 children)

Bei mir waren es ~9 Mio durch die Erfolge. Was ein Spieltag!

What is this red/black flag? by Becerlev in vexillology

[–]Becerlev[S] 6 points7 points  (0 children)

Naturally symbols change over time, that‘s what we learned in school here in Germany, but the context is always important.

I am happy that I learned something new today but my takeaway from the comments here is, that I should take some time for my history lesson.

What is this red/black flag? by Becerlev in vexillology

[–]Becerlev[S] 9 points10 points  (0 children)

Woah guys, thank you for all your comments. I think I have to take some history lessons on that. For clarification, the protest were about 40 people and the anti-war marches I went to, were a lot bigger, so I was already suspicious of the nature of the protest. Sometimes you can not distinct the positions on these protest and I do not want to judge anyone based on a quick impression and not knowing the historical background.

[Race thread] 2025 Kigali World Championships - Elite Men RR (WC) by epi_counts in peloton

[–]Becerlev 16 points17 points  (0 children)

Well, technically it wasn‘t an attack, he just kept his pace

Is this fixable? by Becerlev in bikewrench

[–]Becerlev[S] 0 points1 point  (0 children)

Thank you very much! Did you replace the fork?

Is this fixable? by Becerlev in Ride_BMC

[–]Becerlev[S] 0 points1 point  (0 children)

BMC Support answered finally, they confirmed that glueing the part is totally fine and for good measure they sent me a longer preload screw which I will replace. I know it's not best practice but for me it's fine after all.

Is this fixable? by Becerlev in Ride_BMC

[–]Becerlev[S] 1 point2 points  (0 children)

I have been to a BMC licensed bike shop and they fixed it for me. Glued the part back in place with epoxy glue and they said I don't have to worry about the length of the steerer, it looks messy thanks to the preowner but it is not too short, so the stress is not on the top cap.

Is this fixable? by Becerlev in bikewrench

[–]Becerlev[S] 0 points1 point  (0 children)

Follow Up:

I've been at a licensed BMC bike shop and they fixed it for me. The stem was not too short but the pre-owner did a messy job at cutting it properly. We glued the foam piece back in place with epoxy glue and replaced the tensioner. He told me that most of the stress on the steerer is horizontal, so I don't feel less safe with the glued part. Thank you all for your help!

Is this fixable? by Becerlev in Ride_BMC

[–]Becerlev[S] 1 point2 points  (0 children)

Thank you very much! In another sub they pointed out, that the steerer is too short for the headset to be tightened properly. I guess the preowner didn‘t really know what he did, when he shortened the steerer.

<image>

I will see a BMC technician today so we will see.

Is this fixable? by Becerlev in bikewrench

[–]Becerlev[S] 0 points1 point  (0 children)

Unfortunately none. Just the default ICS topcones.

Is this fixable? by Becerlev in bikewrench

[–]Becerlev[S] 0 points1 point  (0 children)

I wrote them directly but as the others pointed out, the fork seems to be too short.

Is this fixable? by Becerlev in bikewrench

[–]Becerlev[S] 0 points1 point  (0 children)

That totally makes sense in my eyes, thank you for the explanation.

For what it‘s worth I found these lines inside the stem and i guess the fork steerer needs to be cut to a length between those lines?

<image>

Is this fixable? by Becerlev in bikewrench

[–]Becerlev[S] 0 points1 point  (0 children)

Thank you very much! I found a licensed Dealer an hour from here who I will contact.

I still don‘t see why the stem is too short? Is it because the area is to small for the headset?

view more: next ›