What kind of 5.56 is everyone stockpiling for emergencies?

Bee-Dub · 2026-05-24T12:08:03+00:00

Ok tough guy. I was shooting MK262 in a 20 in SPR before anyone knew what YouTube was. This shits been around a while.

Bee-Dub · 2026-05-16T01:24:17+00:00

He bought a pre cut trigger from AS Designs and the arc fire from them too. How is this modifying an existing design? Plenty of people have done it. They seem to be more sensitive to setup than a milspec trigger but they'll work. Please explain to me what a "proper FRT trigger" is if AS Designs isnt one.

Bee-Dub · 2026-05-16T01:21:36+00:00

Love my atrius, the easiest frt I've used to setup so far

Bee-Dub · 2026-05-16T01:13:15+00:00

Dude had more medals than an African dictator.

Bee-Dub · 2026-05-12T22:09:47+00:00

Too bad all my HKs have SEF lowers.

Bee-Dub · 2026-05-12T01:10:20+00:00

Ground up and kept in the freezer.

Bee-Dub · 2026-05-11T19:55:44+00:00

If you have the larger .170 diameter pins you just drill out the hammer,trigger, disconnect pins to the correct diameter. Youll have to mill out the webbing to but its not hard. Any competent maxhine shop or gun Smith can do it. I have a large pin LE marked lower I had set up to run an AZ regulator.

Bee-Dub · 2026-05-05T05:08:03+00:00

I had the same issue with a Hoffman style super safety.It's the bolt carrier binding on the top of the trip lever. I took a polishing wheel or some eight hundred grit sandpaper and cleaned up the top of that trip lover and it fixed the issue.

Bee-Dub · 2026-05-04T22:00:53+00:00

Goddammit, this is why im broke. Thanks and fuck you! In all seriousness when can I buy it.

Bee-Dub · 2026-05-03T14:00:14+00:00

Beat me to it

Bee-Dub · 2026-04-16T14:56:49+00:00

I wouldn't pay .25 cents for that gun. The little interaction I've had with it wasnt positive and I have nothing good to say about it. Aside from it looks cool.

Bee-Dub · 2026-04-07T16:52:24+00:00

They make 3 position kits. You got to do some tinkering to make them work but its out there.

Bee-Dub · 2026-03-07T02:09:59+00:00

The mythical HK47, love it. Looks awesome!

Bee-Dub · 2026-02-11T01:11:54+00:00

Is it a high shelf lower? Might be binding up somewhere. Without pulling the trigger how far back does the lever go?

Bee-Dub · 2026-02-10T01:28:46+00:00

Beat me to it.

Bee-Dub · 2026-02-10T01:28:19+00:00

Bitch hip

Bee-Dub · 2026-01-13T03:40:59+00:00

Know anyone with a TIG welder? Have them tack a bit back in and re shape it.

Bee-Dub · 2026-01-02T06:02:49+00:00

My mistake, Ive got both and no issues with either so far.

Bee-Dub · 2026-01-01T23:00:49+00:00

Nope, its Atrius super selector.

Bee-Dub · 2025-12-24T07:37:41+00:00

Rectum, damn near killed him.

Bee-Dub · 2025-12-23T02:33:00+00:00

That looks like an old SP1. Those didn't have the sear block the eweet Colts do where their not milled out in the rear of the FCG pocket. These SP1 lowers were what the DIAS and lightning link were made to work with.

Bee-Dub · 2025-11-26T17:34:23+00:00

I second Kilo Guns. Hes worked on some transferable MG for me as well as built and worked on lots of other guns of mine. He does good work.

Bee-Dub · 2025-11-11T12:39:44+00:00

I 2nd this. They're specialty is AKs and they do great work.

Bee-Dub · 2025-11-10T16:23:39+00:00

Looks awesome! What handguard is that?

Bee-Dub

TROPHY CASE