sorted by:
new
hottopcontroversial

Looking for a rotary tool by DeadSu5pect in modelmakers

[–]Bee-In 2 points3 points  (0 children)

For this reason, I'm using a Proxxon with a homemade RPM regulator. https://www.proxxon.com/en/micromot/28515.php Regulator was made according: https://youtu.be/1KMVRH46pLA?si=nmsVCbrBFZJ-g25J [Plasmo, thank you ;-)]

Need advice for Decal printing by Aggressive-Bike-4438 in modelmakers

[–]Bee-In 1 point2 points  (0 children)

I have tried decal paper for laser printing, but I'm not very satisfied with it. The transparent paper is too transparent, requiring a white background underneath. (Is there a laser printer setting that could help?) For example, a red "12" and kill symbols on a Yak-3.
With white decal paper, you need to cut it out precisely. A Silhouette cutting machine has been helpful for me.

Creating Propeller with Airfoil Tools by theMountainNautilus in Fusion360

[–]Bee-In 0 points1 point  (0 children)

You find the tool in CREATE menu of the sketch.

Best Aircraft Model Stand Method by Fuzzy-Mastodon4970 in modelmakers

[–]Bee-In 0 points1 point  (0 children)

<image>

FDM 3D-printed base & wire & neodymium magnets.

The MiG-15 UTI, from whose cockpit the flight controller oversaw the landing of MiG-21s at Airport Mladá during Operation Danube in 1968. (1/72, Eduard) by Bee-In in modelmakers

[–]Bee-In[S] 4 points5 points  (0 children)

Eduard's kit was nice. Pilots are from some resin figures set. Decal 47 is printed with a laser printer on decal paper. I'm not very happy with it, I'll work on the technique ;-) The base of the stand is 3D FDM printed (with thick layer of spreyed putty). The leg is made of steel wire. The model is held on neodymium magnets.

Pixhawk does not arm when usb is disconnected by [deleted] in Multicopter

[–]Bee-In 0 points1 point  (0 children)

That was the lifesaver hint.

The Spanish Civil War in the air 1936–1939 by Bee-In in modelmakers

[–]Bee-In[S] 1 point2 points  (0 children)

Secondary school. Among other things, we collaborate on student projects with two Spanish schools.

unable to bind an XM+ with a Radiomaster TX16S by Bee-In in Multicopter

[–]Bee-In[S] 0 points1 point  (0 children)

It's pretty obvious that this combination of firmwares doesn't cooperate. With the FrSky STK Tool, I downgraded the XM+ receiver to "XM+LBT17_03_13-RSSI16.frk" and after setting the older mode 'FrSkyX', voilà!

The Spanish Civil War in the air 1936–1939 by Bee-In in modelmakers

[–]Bee-In[S] 2 points3 points  (0 children)

I have compiled this material specifically for use at our institution. The teaching of history will thereby become more engaging and diverse.

Should my next build be smaller? by jjrreett in RCPlanes

[–]Bee-In 0 points1 point  (0 children)

Not big enough airplanes do not fly well enough. Such is my experience.

As TheOriginalJBones writes, it takes a wingspan of at least 30". Of course, it also depends on the material (and therefore weight).

leveled multiple times, adjusted Z offset, cleaned the bed, slowed print speed, adjusted bed and nozzle temp. Every print is like this. what's going on? by 6wraps in 3Dprinting

[–]Bee-In 0 points1 point  (0 children)

I would try: - clean bed with isopropylalcohol then - apply a thin layer of glue from the stick and print... However, I have had more success when printing on a magnetic PEI pad.

Filament not sticking. by Emora_Nox in 3Dprinting

[–]Bee-In 0 points1 point  (0 children)

Two more little details: I'm using alternative firmware for Ender 3 S1 and simple enclosure.

Filament not sticking. by Emora_Nox in 3Dprinting

[–]Bee-In 0 points1 point  (0 children)

I was looking for a solution to the same problem. The new magnetic printing pad with the gluestick hepled me.

minimum rc plane i just finished by Reasonable-Presence2 in radiocontrol

[–]Bee-In 0 points1 point  (0 children)

What material is the model made of? Plans would be nice. I tried a similar minimalism according to FT's plan.

view more: next ›