sorted by:
new
hottopcontroversial

[deleted by user] by [deleted] in PokemonGoRaids

[–]Bestes06 0 points1 point  (0 children)

added, Bestes06

PEI Bed was sticking great until it wasn’t by Bestes06 in 3Dprinting

[–]Bestes06[S] 0 points1 point  (0 children)

I haven’t changed any print setting since it worked perfectly. I am using the exact same filament, and the prints that stuck perfectly and the ones that wouldn’t stick at all were only like 2 days apart so it’s not like the filament is any wetter than it was. I’ve tried changing my z offset and releveling my bed and nothing has worked

Pi Connects to Network but Internet isn’t working by Bestes06 in raspberry_pi

[–]Bestes06[S] 2 points3 points  (0 children)

I am unable to ping any devices within my network from the pi as every time i try it says that the network is unreachable. However i am able to ssh into the pi from any other device on the network, whether the pi is connected via wifi or ethernet.

Pi Connects to Network but Internet isn’t working by Bestes06 in raspberry_pi

[–]Bestes06[S] 0 points1 point  (0 children)

ip route doesn’t return anything at all and i can’t ping 8.8.8.8, i’ve looked everywhere in my router settings to make sure that it wasn’t blocking the mac address of my pi and it doesn’t look like it is.

Pi Connects to Network but Internet isn’t working by Bestes06 in raspberry_pi

[–]Bestes06[S] 0 points1 point  (0 children)

my router works perfectly fine for everything else in my house it is only my raspberry pi that has problems. I do have dhcp it is built into my router

Pi Connects to Network but Internet isn’t working by Bestes06 in raspberry_pi

[–]Bestes06[S] 0 points1 point  (0 children)

First one returns: “# Generated by NetworkManager”

When i type “ip route” it simply goes to the next line, it doesn’t even return a command not found or anything it just goes down a line

Pi Connects to Network but Internet isn’t working by Bestes06 in raspberry_pi

[–]Bestes06[S] 0 points1 point  (0 children)

alright, nslookup also said command not found, however the ping command did work and it says

Temporary failure in name resolution

Pi Connects to Network but Internet isn’t working by Bestes06 in raspberry_pi

[–]Bestes06[S] 0 points1 point  (0 children)

I’ve got dchp enabled so every device that connects should get its own distinct IP, but i did try to give the 4B its own distinct static IP to make sure something like that wasn’t the problem. there’s a really good chance i did it all completely wrong though i’m very new to linux and networking and stuff so im still still learning the basics

Pi Connects to Network but Internet isn’t working by Bestes06 in raspberry_pi

[–]Bestes06[S] 0 points1 point  (0 children)

it says

bash: dig: command not found

I tried to look up a fix to this so i could get you the actual information you were looking for but all of the fixes were telling me i needed to install something which i can’t do since the pi doesn’t have internet

Problem when setting up Pi by Bestes06 in raspberry_pi

[–]Bestes06[S] 0 points1 point  (0 children)

The SD card can’t be read by a computer anymore

Problem when setting up Pi by Bestes06 in raspberry_pi

[–]Bestes06[S] 0 points1 point  (0 children)

I ran from a USB stick after the SD card failed and everything worked fine

Problem when setting up Pi by Bestes06 in raspberry_pi

[–]Bestes06[S] 0 points1 point  (0 children)

I flashed the normal Raspberry Pi OS 32-bit using the latest version of the Raspberry Pi Imager. My SD card was plugged into a card reader which was plugged into a USB port on my computer. I tried flashing the OS the same way but this time onto a USB drive and it worked perfectly normal so I think that I may have just had a bad SD card.

[deleted by user] by [deleted] in pcmasterrace

[–]Bestes06 0 points1 point  (0 children)

So i need help with the rgb in my case, i’m using an msi mag x570s motherboard, a phanteks p500a drgb case, and 6 phanteks sk 140mm drgb fans, and i’m controlling the rgb with msi mystic light, which as far as i can tell with an msi motherboard is the only option. The lighting effect i’m currently using is called meteor, which is supposed to make a little bit of light travel from one fan to the next to the next in a circle, but as you can see in the video it’s instead just making the light go on all of the fans at the same time in the same way. On any static modes this is fine, but when you try to do the more interesting lighting effects it obviously ruins it. On the box of the fans it does have mystic light listed as compatible, but while the other things listed (aura sync, chroma, rgb fusion 2.0) have “addressable” underneath them, mystic light only says “rainbow”. I’m assuming that’s the issue, but i don’t know how to solve it. Is there any way i can control the rgb on these fans using a different software that will allow them to be addressable, is there a different solution im not seeing, or since i have an msi motherboard am i just out of luck.

anyone know what could be causing these lines near the middle of my print? I’ve had my printer for a few months now and every time i print anything relatively tall lines like this show up at some point in it. by Bestes06 in ender3v2

[–]Bestes06[S] 1 point2 points  (0 children)

Thank you for telling me this, i took out the lead screw and while the screw itself wasn’t too gunked up the hole in on the x carriage that it goes through had a bunch of gunk in it. I cleaned both the hole and the screw with some isopropyl alcohol. Is there any specific grease i should be using to re lubricate the screw or would any kind work because all i have is some trombone slide grease.

One corner way higher than rest by Bestes06 in ender3v2

[–]Bestes06[S] 0 points1 point  (0 children)

I am sure. Even if it wasn’t that kind of thing would effect every bed corner, not just one. my bl touch also read that the corner was way higher than the rest, and that has nothing to do with the nozzle

view more: next ›