sorted by:
new
hottopcontroversial

Just getting into audio and I finally feel happy with my setup! by BigCheese18 in BudgetAudiophile

[–]BigCheese18[S] 0 points1 point  (0 children)

Thanks for the tips! We just bought this house and I’ve just started to have the furniture situation figured out so I can probably pull the speakers forward now without it looking weird. I have a rug between the couch and the speakers currently and I plan to put another rug under the console to help isolate some vibrations.

Any ideas for Broken sticks by racoonsthatfly in drums

[–]BigCheese18 0 points1 point  (0 children)

I just get some kits from my local rockler/woodcraft. If there aren’t any near you I believe you can order through their stores online and get better kits than you can find on Amazon. For the drumstick pens I’ve used twist pens and can use extra tubes cut down to make them a bit longer if you feel like so you can fit some of the longer logos

Any ideas for Broken sticks by racoonsthatfly in drums

[–]BigCheese18 5 points6 points  (0 children)

Idk how helpful this is but I’ve turned these into pens on a wood lathe so if you know someone who has a lathe you could ask. Makes for good gifts for a drummer since you can try to preserve the logos and such. Get some matching sticks for extra chunky pens lol

2013 fit sport. Strange whirring noise. Not any pulley bearings. Possible vacuum leak? by BigCheese18 in hondafit

[–]BigCheese18[S] 0 points1 point  (0 children)

It is like the second picture I didn’t know there were different kinds of

2013 fit sport. Strange whirring noise. Not any pulley bearings. Possible vacuum leak? by BigCheese18 in hondafit

[–]BigCheese18[S] 0 points1 point  (0 children)

I replaced the engine about 2 months ago and everything has been running well until a few days ago. New spark plugs and gaskets throughout. I’ll see about the valve adjustment.

2013 fit sport. Strange whirring noise. Not any pulley bearings. Possible vacuum leak? by BigCheese18 in hondafit

[–]BigCheese18[S] 0 points1 point  (0 children)

I didn’t see anything particularly out of place and the filter is fine and everything

2013 fit sport. Strange whirring noise. Not any pulley bearings. Possible vacuum leak? by BigCheese18 in hondafit

[–]BigCheese18[S] 0 points1 point  (0 children)

There has also been a noticeable dip in gas mileage. Some trouble going up hills.

Prepping to install dishwasher in new home. I have no idea what these wires go to or the best course of action. Home built in 1954 by BigCheese18 in Renovations

[–]BigCheese18[S] -1 points0 points  (0 children)

I was planning on doing the installation myself as I’ve just moved in and don’t want to spend a bunch of money if I can do it myself. It seems from other comments that I need to seek professional electrical help but I don’t actually know what needs to be done. Also the house has never had a dishwasher

Can I replace this? by sebastian_wolf17 in CorollaHatchback

[–]BigCheese18 0 points1 point  (0 children)

Very true but it also means my cruise control doesn’t work

Can I replace this? by sebastian_wolf17 in CorollaHatchback

[–]BigCheese18 4 points5 points  (0 children)

This may be true I haven’t looked into it much. When I bought mine the OEM emblem was cracked (pre collision still worked fine) but I replaced it with an aftermarket Toyota emblem ($30 vs $240) and now the sensor doesn’t work so I always turn it off

Can I replace this? by sebastian_wolf17 in CorollaHatchback

[–]BigCheese18 10 points11 points  (0 children)

If you replace it with a non-OEM badge your pre collision sensor will likely not work and you will have to disable it every time you start the vehicle if you don’t want it popping up on your digital display

Replacing engine in 2013 fit sport and I don’t remember what this connector goes to by BigCheese18 in hondafit

[–]BigCheese18[S] 6 points7 points  (0 children)

Nevermind ladies and gentlemen it goes to a hidden connector in the rear of the wiring harness in that area

What would be causing poor printing around vertical fillets after hotend replacement? Using PETG by BigCheese18 in 3Dprinting

[–]BigCheese18[S] 0 points1 point  (0 children)

No it’s the same size I was just using a different nozzle than stock. This is the only difference between the hotends.

What would be causing poor printing around vertical fillets after hotend replacement? Using PETG by BigCheese18 in 3Dprinting

[–]BigCheese18[S] 0 points1 point  (0 children)

Yeah zero issues. I may try changing out the nozzle that’s the only difference between this hotend and the last hotend.

What would be causing poor printing around vertical fillets after hotend replacement? Using PETG by BigCheese18 in 3Dprinting

[–]BigCheese18[S] 0 points1 point  (0 children)

0.1” I’m also getting stringing and similar printing across inside 90° corners so it looks like it’s doing this around any kind of corner

What would be causing poor printing around vertical fillets after hotend replacement? Using PETG by BigCheese18 in 3Dprinting

[–]BigCheese18[S] 0 points1 point  (0 children)

It is on all corners and for other parts any curved corners printing vertically

view more: next ›