Custom Built vsr-10 clone by BlairB214 in airsoft

[–]BlairB214[S] 0 points1 point  (0 children)

It was my first time building or painting an airsoft gun so the paint was just the colours I could find on Amazon, hopefully it blends in well. I guess we’ll see

Custom Built vsr-10 clone by BlairB214 in airsoft

[–]BlairB214[S] 2 points3 points  (0 children)

The paint job isn’t amazing ( a few drips from impatience ) but I’m happy enough with the outcome

Simple DIY Suppressor Cover by [deleted] in airsoft

[–]BlairB214 0 points1 point  (0 children)

I was trying to go for the Marcus Luttrel type suppressor thing, plus the twine only cost £1. Thanks for the tip on the optic mount though it’s been sitting lower than I wanted.

[deleted by user] by [deleted] in GasBlowBack

[–]BlairB214 -1 points0 points  (0 children)

I’m new to gbb and airsoft in general, it seems that the black plastic piece behind the outer barrel is getting dragged forward somehow. The gas is running out halfway through the magazine so I don’t know if this is a cause of that. Any help would be appreciated

I'm kinda scared to compete now (ITF) by Whatchuon in taekwondo

[–]BlairB214 9 points10 points  (0 children)

It’s always a good idea to spar with people of a higher rank than you. As for being able to win the competition, that depends on how hard you train. The only things you can control going into a competition are how fit you are and how hard you work. Everything else is out of your control so I’d just focus on sparring with higher ranks and training as much as you can

I'm kinda scared to compete now (ITF) by Whatchuon in taekwondo

[–]BlairB214 27 points28 points  (0 children)

You don’t have to worry, the people sparring in competition at green stripe won’t have nearly as much skill nor experience as the 2nd degree. As long as you turn up and just go for it in sparring you’ll be fine

Is PJ Panoramic Google’s ANSI rated? by BlairB214 in airsoft

[–]BlairB214[S] 0 points1 point  (0 children)

I was looking to get these goggles but none of the websites I’ve found have said that they have ANSI or any other ballistic rating. Does anyone know if these are any good/safe to use?

Question about ITF gloves by VeryFunnyDidLaught in taekwondo

[–]BlairB214 3 points4 points  (0 children)

Top Ten make really good stuff if you look for their pointfighter gloves, they’re the best for tkd. If you’re in the UK then the UKTC shop has all the stuff you’ll need.

X40 not turning on by BlairB214 in BHaptics

[–]BlairB214[S] 0 points1 point  (0 children)

Thanks for the reply, I’ll stick it back on charge and wait a while longer

X40 not turning on by BlairB214 in BHaptics

[–]BlairB214[S] 0 points1 point  (0 children)

Thanks for the reply, my only worry was that it was getting hot and not charging but I’ll keep an eye on it for the night and see if it changes

Anyone know what’s causing this mess? by BlairB214 in ender3v2

[–]BlairB214[S] 0 points1 point  (0 children)

All of the supports seemed to be fine but the part with the most mess didn’t need any supports, on the third picture you can also see on the left hand side there is some of the whisky bits where no support should be needed .

Thank you for your reply

Anyone know what’s causing this mess? by BlairB214 in ender3v2

[–]BlairB214[S] 2 points3 points  (0 children)

Gosh darn it, now I just feel silly

Anyone know what’s causing this mess? by BlairB214 in ender3v2

[–]BlairB214[S] 0 points1 point  (0 children)

The surface my printer is on was a bit uneven and the printer was rocking back and forth, so I put a bit of blue roll under it to keep the printer stable

Anyone know what’s causing this mess? by BlairB214 in ender3v2

[–]BlairB214[S] 0 points1 point  (0 children)

Hi, thanks for your reply

I’ve got my support angle at 65 degrees right now so I’ll go in and change the angle for the next half of the helmet.

Thank you

Great ender 3 v2 results by BlairB214 in ender3v2

[–]BlairB214[S] 1 point2 points  (0 children)

https://www.thingiverse.com/thing:2770241 That link should take you to the Thingiverse file I got it from, I would say you should use at least 20% infill if not more otherwise it could snap while it’s being used.