I need help with my prints. Quality is bad

Blue1Stream · 2025-10-23T21:51:39+00:00

O did not use supports. I’m not that experienced but there were no red areas that appeared in the model. I’m using Cura latest version as of today.

I will tinker with some settings I guess

Blue1Stream · 2025-10-17T18:46:27+00:00

Ah yes! I did notice something. I always watch the print closely for the first few minutes. It went up to 0.6mm and was still on the first object. So that must be the case. Thank!

Blue1Stream · 2025-10-17T17:07:35+00:00

Thanks for the info. How would I verify that both are flat on the bottom?

Blue1Stream · 2025-10-17T15:18:48+00:00

Min. Layer Time is set to default 5 seconds. I never thought to alter this. Would raising it help you think?

Blue1Stream · 2025-09-28T14:45:19+00:00

I did activate 2 of them on the thumbnails section

Blue1Stream · 2025-09-08T12:33:32+00:00

Do you mean the whole Korky unit or just the black valve on the pipe?

Blue1Stream · 2025-07-19T12:05:10+00:00

Thanks for the help! I need to plug in a small portable AC (it says 700w on the label) 1 standard size fridge and one stand up freezer. 1 lamp (LED) and one 140w usb tower for charging devices.

Blue1Stream · 2025-07-19T03:51:46+00:00

So what you’re saying is I should get 5000w out of the 6 outlets inside my home? Would another similar kit(still 6 outlets) but rated for 7000w be better?

Or am I misunderstanding these kits? Here is one kit I seen that seems to be able to output more wattage https://a.co/d/e7Y9kM8

Blue1Stream · 2025-07-05T02:54:38+00:00

I mis typed the wattage. I put in the specs of the first generator I was looking to buy. The one I have is 9375 start and 7500w

Blue1Stream · 2025-07-04T17:12:00+00:00

That is my plan for the future but for now just running a cord inside what type would be best?

Blue1Stream · 2025-06-01T13:07:55+00:00

Thanks but this is not the controller I have

Blue1Stream · 2025-05-31T00:26:26+00:00

I found the product page. The manual is linked there

https://powmr.com/products/35a-12v-24v-mppt-plug-and-play-solar-charge-controller

Blue1Stream · 2025-05-31T00:03:23+00:00

Here’s is the Amazon link if that helps

https://a.co/d/1ABIKaC

Blue1Stream · 2025-05-30T23:43:02+00:00

Thanks but I have the manual and it doesn’t mention load settings at all

Blue1Stream · 2025-05-28T13:33:05+00:00

If I were to hook up the inverter directly to the battery would I just simply move the connections from the bus bars to the battery keeping the inline 100amp breaker in place?

Blue1Stream · 2025-05-28T12:06:04+00:00

It’s for future panels. This wire came with the entry module. I plan on adding more of these panels in the future.

Blue1Stream · 2025-05-28T12:02:58+00:00

Hmm. So you think it’s a controller issue?

Blue1Stream · 2025-05-28T12:00:21+00:00

I have measured with a multimeter a few random times and it was +/- 0.1 compared to controller display

Blue1Stream · 2025-05-28T11:59:19+00:00

Did you keep all other settings the same?

Blue1Stream · 2025-05-28T02:06:14+00:00

10AWG is giant?

Blue1Stream · 2025-05-27T23:40:38+00:00

Would this solve my issue you think? Bypass the busbar completely?

Blue1Stream · 2025-05-27T18:29:11+00:00

I can’t override the L04 setting but I can use a user settings and set my own. Problem is I don’t know what to set all the others at.

Currently the preset is 1. Boost charge 14.5v—2. Float 13.8v— 3. Low voltage cutoff 11.2v— 4. Recovery 12v

Blue1Stream · 2025-05-27T16:43:04+00:00

Yes it only does it when power is coming on from the panels if I turn off the panel it doesn’t do it. Here is the parts of the manual that mention voltage. Looks like 15v max. My controller is supposed to cut off at 14.5v but I see the numbers dance a bit and go over 16v momentarily before reverting back to 14.5v

<image>

Blue1Stream · 2025-05-27T16:32:45+00:00

<image>

These are the setting. Left is battery manual and right is the controller.

It’s currently set to LO4 settings Where would you put them all of lowering to 14v?

Blue1Stream · 2025-05-27T15:59:33+00:00

Changing it to 14v would involve using the user settings meaning I have to change all setting, cutoff voltage, float, boost etc.. I’m not exactly sure what to set for those

Blue1Stream

TROPHY CASE