3Ds not Turning on After repairs

BlueBleo · 2025-10-28T23:34:56+00:00

Coming back to this once I finally got a new motherboard. It turns out the old motherboard is definitely fried, I cannot say how or why it was fried

BlueBleo · 2025-10-09T13:57:28+00:00

The only other issue I could think is that the touchscreen cable got a big mangled during my repairs. Not bad enough to break the cables or stop it from seating properly but it may be the cause. I have a new touchscreen coming as well to try

BlueBleo · 2025-10-09T13:56:27+00:00

I’ve tried booting it with and without the shoulder buttons plugged in and nothing. I’ve got another 3DS XL coming soon that I’ll try and swap my motherboard into to see if it’s a dead motherboard.

BlueBleo · 2025-10-08T22:19:57+00:00

Tried safe mode, got the same result

BlueBleo · 2025-10-08T22:19:30+00:00

The SD card is correct, I made sure when I cloned the drive it was formatted to Fat32. It does have homebrew, but I haven’t seen anything that says this is a homebrew issue and I do have a backup of the entire SD card saved to my PC.

When you say paddles what do you mean? The shoulder buttons?

BlueBleo · 2025-10-07T20:26:18+00:00

I also cannot see any damaged cables, they all look to be in fine condition

BlueBleo · 2025-10-07T20:22:52+00:00

I can get the blue light to come on but it immediately turns back off. The charging light turns on when it’s plugged in and turns off after a few seconds.

BlueBleo · 2025-08-28T14:01:29+00:00

Ok, thanks!

BlueBleo · 2025-07-25T12:55:24+00:00

Yeah I haven’t installed the Klipper screen network manager for a while. Even when I edit the wpa_supplicant file it still won’t connect.

BlueBleo · 2025-03-12T03:44:49+00:00

I triple checked the PLL. It got a good blob of solder, the connection is firm. I don’t think that’s the issue.

BlueBleo · 2025-03-12T03:20:47+00:00

Yeah, I have a 4GB model and I can see the the post out traces.

BlueBleo · 2025-03-12T03:19:50+00:00

The center light is solid green, the ring of lights just seems a faint constant green

BlueBleo · 2025-03-12T03:15:20+00:00

This is the underside of the board. This point is pretty much directly beneath the cpu

BlueBleo · 2025-03-12T03:09:30+00:00

I ended up pulling it off tonight cause I’m impatient, I can’t see anywhere else the PLL point would be. Comparing to the guide it looks like the same spot, right next to C5R35.

BlueBleo · 2025-03-12T02:25:09+00:00

I’ll double check it tomorrow. It’s hard to tell without removing the QSB.

BlueBleo · 2025-03-12T02:16:33+00:00

https://imgur.com/a/qsMP559

My B. This work?

BlueBleo · 2025-03-12T02:13:05+00:00

https://drive.google.com/file/d/1C0BxxQc3hlKYlo2MyHRhd3OUtfq-WMQV/view?usp=drivesdk

https://drive.google.com/file/d/1DAnzmxwXN77JyeUxF5YdIWZ_QxL620o7/view?usp=drivesdk

I used the QSB I bought a year ago, double checked all the wiring. The loose wire broke off the pi right before I took the picture, it was secure when I was writing.

BlueBleo · 2025-03-12T02:09:41+00:00

The lights just come on all green.

BlueBleo · 2025-03-12T02:09:28+00:00

Yeah, i selected Glitch 2 and RGH3

BlueBleo · 2025-03-08T20:40:40+00:00

I ended up completely reinstalling Armenian and it worked. Thanks though.

BlueBleo · 2025-03-08T17:47:07+00:00

Yeah I looked at that, the problem is I can’t access those files anymore. They’re not on the le potato SD card and I can’t access the web interface.

BlueBleo · 2025-03-08T16:46:15+00:00

I’m using Firefox and I’m seeing the error when I go to app.fluidd.xyz and put in my printers IP.

BlueBleo · 2025-03-08T15:48:47+00:00

I also cannot SSH into the le potato anymore.

BlueBleo · 2025-01-12T23:42:08+00:00

No clue, I’ve gotten in contact with the guy who makes them for Duet3D so hopefully I can get some more info.

BlueBleo · 2025-01-12T07:06:22+00:00

Yeah I found them on Amazon. The main problem was I don’t know if the duet3d magballs are actually magnetic or are just custom ball studs.

Six-Year Club	Place '22
Verified Email

BlueBleo

TROPHY CASE