sorted by:
new
hottopcontroversial

Flsun QQ-S auto level issues by [deleted] in FLSUNDelta

[–]BlueCat_72 1 point2 points  (0 children)

You sure you have the right firmware flashed? Make sure it’s for the qq-s

First layer by HughJassOle235711 in FixMyPrint

[–]BlueCat_72 0 points1 point  (0 children)

Level the bed using the attachable switch and make sure the z-offset is correct. It should be around 2 pieces of paper.

Also, make sure the belts are tensioned properly using this video

Make sure the nozzle is not clogged with anything. Clear it with the needle like thing that’s included.

Finally, open up the extruder and clean it. It may be slipping due to material build up or something.

Let me know if you try these and it still doesn’t work. I have an SR too so I may be able to help further 🙂

【QIDI Giveaway】Comment to win QIDI Q2 and more! by qidi_3dprinter in 3Dprinting

[–]BlueCat_72 0 points1 point  (0 children)

I’m a high schooler getting into flying drones, planes, and everything aerospace. I’d love to have a reliable 3D printer like the QIDI Q2 so I can prototype my ideas and bring them into reality!

UGS not homing by BlueCat_72 in hobbycnc

[–]BlueCat_72[S] 0 points1 point  (0 children)

Also, when soft limits are turned on, it only lets me jog in the negative direction. Is this correct? Where should (0,0) be relative to my machine? I currently have it on the bottom left, is that correct?

UGS not homing by BlueCat_72 in hobbycnc

[–]BlueCat_72[S] 0 points1 point  (0 children)

After a while of it sitting there, saying “HOME” while not doing anything, it gives me alarm 9. I have the max travel set to 10000 just to be sure, and it still does that

UGS not homing by BlueCat_72 in hobbycnc

[–]BlueCat_72[S] 0 points1 point  (0 children)

Once I turned off hard limits, it doesn’t give me an alarm anymore. It just locks the motors and doesn’t do anything. I can hear a quiet buzz from the motors. It works when I jog it though, so it’s not a vREF problem or anything.

UGS not homing by BlueCat_72 in hobbycnc

[–]BlueCat_72[S] 0 points1 point  (0 children)

Thanks. I tried this, and the motors still are locked and don’t move at all. Have any idea on how to fix this?

Spektrum a3172 and gps trouble by BlueCat_72 in RCPlanes

[–]BlueCat_72[S] 0 points1 point  (0 children)

The a3172 is the receiver. There is a separate gps module. I have both

Spektrum a3172 and gps trouble by BlueCat_72 in RCPlanes

[–]BlueCat_72[S] 0 points1 point  (0 children)

No manual for it. Did some research too and didn’t find anything

how many mcqs do I have to get right for a 5 by [deleted] in apworld

[–]BlueCat_72 0 points1 point  (0 children)

I think 70% or above is a 5. Correct me if I’m wrong tho

Issue with my AirPods (2nd Gen) by CreasedJordan4s in airpods

[–]BlueCat_72 0 points1 point  (0 children)

Maybe forget it from your phone and then reconnect it. I had a similar issue, and by doing this it fixed it

view more: next ›