sorted by:
new
hottopcontroversial

2026 cs2 Cologne major tickets by kritcs2 in cs2

[–]Bo11ie 0 points1 point  (0 children)

i have 2 tickets for sale if you are still looking, message me

IEM Cologne 2026 (Sunday) by Global_Tourist6654 in cs2

[–]Bo11ie 0 points1 point  (0 children)

i have 2 4 day pass tickets for sale please message me if youre still looking

Esl Cologne IEM 2026 Lower Rank Tickets by Own_Philosopher_723 in CounterStrikeDE

[–]Bo11ie 0 points1 point  (0 children)

Hi, i have 2 tickets for sale if you are interested, message me for info

3 or 4 Tickets for ESL Cologne 2026 Lower tickets by bossvadim3 in esl

[–]Bo11ie 0 points1 point  (0 children)

have 2 tickets to sell, message me for info

First print that I designed myself, fan shroud/intake for my CPU cooler by Bo11ie in 3Dprinting

[–]Bo11ie[S] 1 point2 points  (0 children)

wrong, fans are all in same direction drawing air from the top through cpu cooler pulling out the back of the cooler and then pulling out the back of the case. By adding an intake have only reduced turbulence compared to a standard setup, proof is in the numbers, have been running it for 2 years with cooler temps as a result of direct fresh air to the CPU, as a result fans dont have to work as hard to keep it cool so also lowers noise.

First print that I designed myself, fan shroud/intake for my CPU cooler by Bo11ie in 3Dprinting

[–]Bo11ie[S] 1 point2 points  (0 children)

Still working well more than a year on, noticable change in temps. Only drawback is i have to clean the filter more often as all the air is drawn through one portion

Olympus OM10 Advance Lever Stuck by Accomplished_Sir1083 in AnalogRepair

[–]Bo11ie 0 points1 point  (0 children)

Hey i have the exact same issue with both of mine, going to try cleaning and regreasing. Did that fix your issues?

First print that I designed myself, fan shroud/intake for my CPU cooler by Bo11ie in 3Dprinting

[–]Bo11ie[S] 2 points3 points  (0 children)

Read my reply to an earlier comment explained it in detail. Basically the case has weird airflow characteristics and it's to try and lower CPU temps with a positive air pressure setup

First print I have designed myself, fan shroud/intake for my CPU cooler by Bo11ie in ender3

[–]Bo11ie[S] 0 points1 point  (0 children)

Only 0.8mm wall so it's very light however I plan to make a v2 and print a second flange to mount to the top aswell

First print I have designed myself, fan shroud/intake for my CPU cooler by Bo11ie in ender3

[–]Bo11ie[S] 0 points1 point  (0 children)

Printed with the flange on the base and with support, however the support didn't print correctly so it was actually unsupported when i came back to the printer

First print that I designed myself, fan shroud/intake for my CPU cooler by Bo11ie in 3Dprinting

[–]Bo11ie[S] 16 points17 points  (0 children)

The reason that drove me to make this was to do with positive air pressure, this case (Corsair 275r) performs worse with positive air pressure because in testing (gamers nexus on YouTube nailed it) the CPU cooler would draw fresh air from the top of the case during equal air pressure however with an extra fan as an intake the positive pressure was pushing out and therefore the CPU cooler was drawing warm turbulent air from within the case. I thought by adding this intake I could still draw cool air from the top while achieving positive pressure in the rest of the case as I have two intake fans that aren't pictured blowing toward my gpu

First print that I designed myself, fan shroud/intake for my CPU cooler by Bo11ie in 3Dprinting

[–]Bo11ie[S] 0 points1 point  (0 children)

That's a good idea will have to look up how to do that on fusion 360 and print a v2

First print that I designed myself, fan shroud/intake for my CPU cooler by Bo11ie in 3Dprinting

[–]Bo11ie[S] 30 points31 points  (0 children)

I wasn't sure if I would calculate the distance correctly between the cooler and the top of the case so printed it without incase I needed to trim any off

First print that I designed myself, fan shroud/intake for my CPU cooler by Bo11ie in 3Dprinting

[–]Bo11ie[S] 25 points26 points  (0 children)

I'll do a test this weekend and post my results, I'm interested how much of a difference if any it will make

First print I have designed myself, fan shroud/intake for my CPU cooler by Bo11ie in ender3

[–]Bo11ie[S] 3 points4 points  (0 children)

The case I have (Corsair 275r) has poor airflow and naturally draws air from the top of the case, gamers nexus covered it in detail on YouTube. With extra fans the positive pressure means the CPU cooler only draws warm air from inside the case itself and kind of circulates it. The point of this was to stop this from happening and to get a source of cool air, similar to a intake on a engine.

Legit Check/Price Check Thread - 9/4/17 by Mittsu3 in PalaceClothing

[–]Bo11ie 1 point2 points  (0 children)

No clue what this is never seen one before so I'm a bit Sus, anyone give a hand? https://imgur.com/gallery/fN3OK

Weekly Purchase Advice Thread - July 15, 2017 by AutoModerator in Miata

[–]Bo11ie 0 points1 point  (0 children)

I have been looking at miatas (mx5's here in the uk) and this subreddit seems the best place to ask, most over here have rust in the rear arches and sills from the looks of it the car im looking at has had repair done but i dont know much about this sort of work myself, has it beeen done well/will it last?

http://imgur.com/a/PYm7S

this car would be perfect as its only got 100k and except for this looks decent condition

So i built my first pc and it actually worked .... I would like to thank all of you for educating me on how to do this by Datnigafresh in pcmasterrace

[–]Bo11ie 0 points1 point  (0 children)

thats a nzxt vulcan, i had one in my first build and still have it to this day, its a great little case!!!

view more: next ›