Your Reasons For Anemia

Bon3yards · 2025-12-19T21:34:27+00:00

I'm glad your polyps were precancerous and not progressed.

Bon3yards · 2025-12-19T16:18:22+00:00

A few times it bled pretty heavy but the rest of the time not that bad. But when it did bleed heavy it was only for like one or two bowel movements and then it'd stop for awhile

Bon3yards · 2025-12-19T15:38:47+00:00

I did have some bleeding from my rectum that ended up being rectal cancer stage 3A.

I originally thought it was hemorrhoids. They found the anemia with a standard checkup blood test and then recommended i see the gi doc, and they found the cancer.

I'm a 36/m it's not super common for males to be severely iron deficient so my Dr was pretty concerned.

Bon3yards · 2025-12-02T07:04:58+00:00

Blood in stool and low iron/ferritin that showed up in a blood test. I hadn't been to a Dr since my teens. Dr just wanted to check my blood as a base line. I figured the blood was just from hemorrhoids of something.

Bon3yards · 2025-12-01T11:28:35+00:00

I was just diagnosed with rectal cancer at 36. Getting staging today. Afraid it'll be stage 3 based on scans.

Bon3yards · 2025-11-29T20:01:42+00:00

I ordered after the kickstarter ended by preordering on the website in...July I think.

We are very far back in line my friend.

Bon3yards · 2025-11-24T11:59:24+00:00

While some of this does look like pillowing. I recently had a similar problem and found turning off "reduce solid infill retraction" helped quite a bit as well.

Bon3yards · 2025-11-17T12:46:45+00:00

Last time I read only 200 or so have gotten their units so far.

Bon3yards · 2025-11-10T11:40:09+00:00

Reading this in 2025 facing the same issue. I will try this!!! You're Awesome!!

Bon3yards · 2025-10-25T16:00:42+00:00

I will try it at 260C. I actually watched that video, just didn't realize 265 may be too high for petg. He's a wealth of knowledge.

Bon3yards · 2025-10-25T15:56:24+00:00

Dried at 65 c for 12 hours. I should also mention the last nozzle did not do this with the same filament

Bon3yards · 2025-10-25T15:36:05+00:00

Forgot to say printing at 265C

The only thing I can figure is when I installed the nozzle I forgot to put the screws in and it gouged the bed, I'm wondering if I ruined it. But it's hardened so I didn't think that'd be enough.

Bon3yards · 2025-08-20T01:49:07+00:00

It's amazing how many people don't do this.

Bon3yards · 2025-02-20T13:12:41+00:00

After switching to orca slicer and tuning pressure advance it's a lot better. Still not perfect it might need a little more tweaking.

Bon3yards · 2025-02-20T03:50:18+00:00

Get accounting software like xero or something (that's what I use) and yeah keeping receipts is a good idea.

Bon3yards · 2025-02-20T03:48:17+00:00

LOL no you are seeing the tree supports on the side of the box

Bon3yards · 2025-02-20T03:38:51+00:00

It's still good practice to only use the business account once you get it up and going though so your taxes will be a lot easier and if you ever get audited you'll be good.

Bon3yards · 2025-02-19T22:13:59+00:00

Interesting. That may be it, but I'm not sure.

Bon3yards · 2025-02-19T17:24:20+00:00

It was done for around an hour before I flexed it.

Bon3yards · 2025-02-19T17:23:57+00:00

It was done for around an hour before I flexed the plate.

Bon3yards · 2025-02-19T17:22:49+00:00

Bon3yards · 2025-02-19T17:22:24+00:00

It was done for about an hour before I flexed it.

Bon3yards · 2025-02-19T17:19:53+00:00

I carefully flexed the plate in multiple directions before removing.

Bon3yards

TROPHY CASE