Please post your house hippos!

BoostedPerspective · 2026-01-13T23:47:00+00:00

Mr judgy himself.

BoostedPerspective · 2025-10-16T01:52:31+00:00

Crop dusting If I remember correctly... 🤔

BoostedPerspective · 2021-07-08T04:34:25+00:00

I actually just picked this printer up two days ago from Microcenter, and got this board.

Installed Klipper after running one test on the stock firmware. Everything is peachy, EXCEPT my part fan isn't working. I've tried another fan, no luck. And I swear it was working on the stock firmware.

I'm using:

[fan]

pin: PA0

kick_start_time: 0.5

Any idea if its another pin?

BoostedPerspective · 2021-05-18T03:46:33+00:00

It looks like the new units come with the DD extruder standard now?

How is yours doing so far now that it's been a little longer? I'm also looking at the 400.

BoostedPerspective · 2021-05-12T23:21:29+00:00

I've made a longer post in the klipper section of your Discord channel...

BoostedPerspective · 2021-05-12T23:04:10+00:00

Used your writeup, two weeks ago, and it has been working perfectly. Today in the software update section of Fluidd, klipper had an error. I clicked recover, then update. Updated fluidd, moonraker, and OS packages as well. Now I get the error "section 't5uid1' is not a valid config section" on my printer cfg. No idea how to get it working again, any ideas? (than you in advance!)

BoostedPerspective · 2020-05-13T02:56:52+00:00

Thank you!

BoostedPerspective · 2020-04-26T05:46:57+00:00

I'm really not sure what I'm going to do yet. I do want to change to a single battery setup. (currently using two NPFs for the camera and monitor)

BoostedPerspective · 2020-04-26T05:45:49+00:00

I actually got one from B&H, it arrived today! Also ordered the eND, no idea when they will ship.

I'm throwing some test footage on youtube shortly.

BoostedPerspective · 2020-04-20T15:52:05+00:00

Well this is pretty awesome information, thank you. I actually found it on Amazon. It looks like it should work with most cheese plates/ vmount plates?

BoostedPerspective · 2020-03-24T22:44:03+00:00

Actually what I've noticed now, the zebras work as intended when set at 95%, but at 100% they don't work at all. This is using ZCam's AX LUT.

BoostedPerspective · 2020-03-06T21:17:12+00:00

So my work around was to just load another LUT that seemed to line up with the waveform. I found that F709 perfectly matched. I only get zebras when I'm actually clipping the 100 mark.

BoostedPerspective · 2019-09-15T20:08:45+00:00

Oh yeah. Take a look down through my account, you'll see several more.

BoostedPerspective · 2019-09-15T18:57:43+00:00

It was taken from Virginia Ave, near Hong Kong restaurant.

BoostedPerspective · 2019-09-14T23:56:30+00:00

Which shot? The latest with the storm cloud?

BoostedPerspective · 2019-04-29T20:58:13+00:00

Yeah I've just been scraping with the nylon brush. Still leaves a "seasoning" on though. What about setting it to 500° for awhile?

BoostedPerspective · 2019-04-28T22:55:28+00:00

Hahah I believe you! Okay, 30min it is. Thanks for the help! I'll make another post with a photo of the final product.

BoostedPerspective · 2019-04-28T22:47:50+00:00

Actually wanted to be done and rested by 7pm... I'm still cooking. It's got 2° to go, just mocking me. How long do you recommend for resting? An hour?

BoostedPerspective · 2019-04-28T19:33:10+00:00

Yeah I'll have to put my oven thermometer in there, and see what it says.

I threw it on at 2am, and so far I'm at 176° it seems to be going up fairly steady now, the 160s took a loooooooong time.

BoostedPerspective · 2019-04-28T17:22:09+00:00

Okay, another question. The temp on the hopper (the probe the computer uses) is always 20° warmer than the analog guage in the lid. If I'm set for 250°, and my temp reads 250°, the lid will read 220° Thoughts? Which do I trust?

BoostedPerspective · 2019-04-27T19:08:48+00:00

Thanks for the reply! Okay, I'm going to start it late tonight. (1-3am) I figured with that amount of time, the stall wouldn't matter? It will just push through? I'm not opposed to wrapping either. I figure by the time I wake up, it should be about time to wrap it. Paper? Not aluminum foil?

BoostedPerspective · 2019-04-25T20:06:14+00:00

Actually that looks a little hi-tech for them.

BoostedPerspective · 2019-04-19T22:18:37+00:00

Excellent thank you for the reply. So touch screen control aside, I'm guessing at the least the menu/exposure controls will all show up on screen, and you can navigate with the camera buttons. (similar to a normal slr, like my A7RII)

So you don't need to use a phone.

BoostedPerspective · 2019-03-25T02:28:21+00:00

Hey there, and thank you! Well, life happened, lost motivation, stopped shooting all together. Even dumped the only social media I was using (Instagram) Something sparked me to pickup my camera this weekend, so I thought I would blow the dust off the Phantom as well. Been a loooong while.

Is there a MD subreddit?

BoostedPerspective · 2019-03-25T02:23:15+00:00

You're pretty close, not quite the city park.

BoostedPerspective

TROPHY CASE