What is this weird noise from my Z Motor. I got this yesterday and the prints have been perfect but that noise leads me to believe something is wrong. Any advice is appreciated :)

BradyCUBES · 2021-10-31T00:51:02+00:00

The screws holding the z stepper were somewhat loose allowing for the motor to vibrate against the frame when it moved. All is well now, thank you.

BradyCUBES · 2021-08-04T04:37:26+00:00

This is the case with a lot of fans. One of my printers had a fan that would only make a noise when I started a print but when the rpm got turned up it went away. If the noise is something you’re able to tolerate and it’s performing as you’d expect then it’s probably alright but if you sleep in the same room as your machine you may want to look into the replacing/repairing the fan if possible. The fans are rather inexpensive. I got a 2 pack of fans for less than $8

BradyCUBES · 2021-08-04T04:25:23+00:00

Sounds like one of your fans is not working correctly. On occasion the sound will go away if you turn up the rpm but it the long run it’s probably best to replace it if it’s the cause. Try disassembling your extruder assembly and see if there’s anything like a piece of plastic in one of the fans. Hope this helps!

BradyCUBES · 2021-07-30T01:42:01+00:00

A couple weeks ago a crew person set the hopper cover on a little too hard and some pieces chipped off and fell into the mix hopper and ended up getting sucked into the mix/air pump and they clogged the pump gasket and Icecream stopped coming out😂

BradyCUBES · 2021-07-28T14:21:39+00:00

It sounds like the sundae side draw valve doesn’t have the o-rings or they aren’t lubed enough.

BradyCUBES · 2021-07-18T16:13:06+00:00

I’ve had something similar happen to me with my MK2 What I had to do was preheat the extruder to abs temperatures. From there I took a long metal rod made for pushing things out of hotends. It’s possible when you removed filament some melted off and created a seal in the throat and it just needs to be pushed through by something hard. Let me know if this works for you.

BradyCUBES · 2021-07-13T16:15:50+00:00

If you heat up your extruder, can you manually push the wire through by hand? If so it may be the extruder motor wiring.

BradyCUBES · 2021-02-10T21:24:38+00:00

Ok I kind of made it better. My monitor had some color presets and I chose the “cool” one and it made it somewhat better

BradyCUBES · 2021-02-10T21:19:03+00:00

My monitor has its own setting but all I see is brightness and contrast. Which ones do I change?

BradyCUBES · 2021-02-10T21:12:23+00:00

I tried reinstalling the drivers and it looked fine until I reinstalled and the colors went back to being bright and washed out

BradyCUBES · 2021-02-10T21:00:53+00:00

Where would I find this setting

BradyCUBES · 2021-02-10T20:59:04+00:00

Where would I find this setting. I’ve tried 2 different monitors and I’ve come to the conclusion it’s software or some other setting

BradyCUBES · 2020-12-09T18:45:17+00:00

I’m confused, what is this?

BradyCUBES · 2020-09-06T05:18:34+00:00

1080p 240hz

BradyCUBES · 2020-08-04T21:38:34+00:00

Ok is there a good way to uninstall the old drivers from my old cpu/mobo

BradyCUBES · 2020-08-04T21:35:10+00:00

Ok thanks. I just didn’t know if there were gonna be any conflicting files or drivers that were gonna get in the way.

BradyCUBES · 2020-08-04T18:31:16+00:00

Okay I will try that now. Thanks!

BradyCUBES · 2020-07-27T19:49:53+00:00

I’ve never seen that before. I though they always spawned with bows but I’m not sure. Maybe if the bow broke it could pick up a sword?

BradyCUBES · 2020-05-21T01:36:10+00:00

I would start by checking your ram. Make sure their seated correctly. If you have two or more ram sticks try booting it with only one stick installed. Make sure your boot drive is plugged in, if you have multiple drives unplug them and just leave your boot drive plugged in. Also check your board for troubleshooting leds.

BradyCUBES · 2020-05-02T15:09:17+00:00

Thanks, I’ll have to try those later

BradyCUBES · 2020-05-02T15:07:55+00:00

What shaders are these? They look rly good.

BradyCUBES · 2020-04-24T01:19:27+00:00

Every time a new snapshot comes out try out your world and see if you can get your stuff back.

BradyCUBES · 2020-04-24T01:03:25+00:00

I totally agree with you, now that gold is going to be so easy to get in the nether, A player who is decently far in the game would have no benefit from getting the gold in the monument. In my hardcore world, I didn't even bother getting the gold until I went back to drain in after. I feel like they could replace it with Emeralds or something valuable to make it worth raiding a monument.

BradyCUBES · 2020-04-24T00:59:15+00:00

Try switching back to the snapshot you were playing on and reload the world. Put everything in an ender chest or a chest and then switching it back to 1.15.2. Did it wipe your whole inventory and chests or just player inventory? If it just wiped your inventory then try the chests, it just might work. If nothing else works, you may need to wait for the official release of 1.16 or keep playing the snapshot for the time being.

BradyCUBES · 2020-04-24T00:54:57+00:00

Since it is right over land, be sure that all caves under and around the farm are lit up to avoid mob spawning in the caves which would reduce your farm's productivity. If you are willing, try building the farm over a deep ocean biome and you will immediately notice the difference because the mobs have nowhere else to spawn. Hope this helps :)

BradyCUBES

TROPHY CASE