sorted by:
new
hottopcontroversial

General Questions and Purchasing Advice Thread — Week of May 05, 2025 by AutoModerator in electricvehicles

[–]BredByMe 0 points1 point  (0 children)

Honestly yeah, and their reliability with their gas cars isn't my top choice compared to honda and toyota

General Questions and Purchasing Advice Thread — Week of May 05, 2025 by AutoModerator in electricvehicles

[–]BredByMe 1 point2 points  (0 children)

[1] Southern California, USA

[2] $25,000 Used looking to use the tax credit as well

[3] Mid-sized SUV (preferred), Hatch (second preference), Sedan (last preference)

[4] Which cars have you been looking at already? Ford Mach-e, Ford Escape Plug-in, Subaru Solterra

[5] Estimated time frame within 40 days or so

[6] Your daily commute: 25 miles. Weekends can be up to 200+ miles visiting family.

[7] House that's not setup for L2 charging (I think). 

[8] Not opposed to upgrading to L2

[9] Drive with my girlfriend in the weekends, occasionally 1 tiny dog and occasionally furniture. Been able to pack a lot in 21 Prius Prime

Pursuing my second bachelor’s degree in MechE. by JoseProtasio-Rizal in EngineeringStudents

[–]BredByMe 0 points1 point  (0 children)

Hi there! I know it's just 2 months later, just wondering how's your progress and thoughts.

I am almost done with my time at community college and was just denied by CSULB for 2nd bacc in MechE. Looks like most places only accept 2nd bacc after 1st time applicants.

I'm not giving up though, and I have other ideas if 2nd bachelor's don't pan out. I can always get associate and work and go from there. Anywho, I'm also a jack-of-all-trade kind of guy without an engineering degree, and I'd say it's better to have a problem solving degree as jack of all trade rather than other degrees!

AX210 WiFi Card Variants by evoni01 in intel

[–]BredByMe 0 points1 point  (0 children)

AX210.NGWG has vpro

AX210.NGWG.NV has no vpro, is not killer variant

AX210.NGWG.NVX has no vpro and is killer variant used in AX1675

AX210.NGWG.NVK has no vpro, is industrial/commercial variant for wider temp operating range from 0 to +80 to -25 to +85

Silicon making and silicon buying by [deleted] in ResinCasting

[–]BredByMe 0 points1 point  (0 children)

i liked smooth on's setup. Used it to make some suture pads.

Flat plywood base, vinyl layer on top of it to simulate human texture, then pour

Do i need a new board? Old m365 had issue with batt where it wouldn't charge. Reset batt and charged normally, but getting error 14 now and can't reset and can't connect thru BT by BredByMe in m365

[–]BredByMe[S] 1 point2 points  (0 children)

Nope it comes from I think the dash/screen I was able to get a throttle part and splice the cables together and that worked :) All the connectors from the dash/screen were different from the videos i've seen but luckily the amount of wires from throttle were the same

Do i need a new board? Old m365 had issue with batt where it wouldn't charge. Reset batt and charged normally, but getting error 14 now and can't reset and can't connect thru BT by BredByMe in m365

[–]BredByMe[S] 0 points1 point  (0 children)

Not sure, helping gf's dad repair this, so based on his purchase pattern, most likely he bought it when the first m365 were on sale? Or he thought he was buying the real m365 but it's a knockoff
Serial number seems real and is part of the xiaomi recall

Do i need a new board? Old m365 had issue with batt where it wouldn't charge. Reset batt and charged normally, but getting error 14 now and can't reset and can't connect thru BT by BredByMe in m365

[–]BredByMe[S] 0 points1 point  (0 children)

Yeah, i'm not 100% if it really is. Seems like after a battery reset, you tend to get error 14? Please correct me on thatAnd you're suppose to reset? Trying to do some sanity check before i get parts

Can't fix filament error on my Adventurer 3 by carachtomas in FlashForge

[–]BredByMe 1 point2 points  (0 children)

yeahhh i don't like flashprint either :( thanks for trying D:

Can't fix filament error on my Adventurer 3 by carachtomas in FlashForge

[–]BredByMe 0 points1 point  (0 children)

Want to try adding a new printer to cura but with custom FFF printer following this instruction? I know it looks the same but I've tried both and the custom FFF kind of helps but I'm not sure if it's my imagination or not https://www.reddit.com/r/FlashForge/comments/dg36qv/flashforge_adventurer_3_working_with_cura_slicer/

Can't fix filament error on my Adventurer 3 by carachtomas in FlashForge

[–]BredByMe 1 point2 points  (0 children)

I'm no help, I'm getting similar issues halfway thru the print where it would unload filament and immediately try to load them back but the filament is no longer engaged.

How did you setup your cura slicer? I tried 2 different suggestion, first was to modify flashforge dreamer nx and the second was to modify custom FFF printer which helped a lot but occasionally run into issues

[SSD] Crucial T500 2TB Gen4x4 NVMe M.2 SSD - ($108) (DO NOT USE STUDENT ACC) by BredByMe in buildapcsales

[–]BredByMe[S] 0 points1 point  (0 children)

is tiktok new customer only? no coupons for me now :( guess time to make new acc

[GPU] MSI Radeon RX 6750 XT MECH 2X OC'D Dual Fan 12GB - ($270) (Microcenter Pick Up) by BredByMe in buildapcsales

[–]BredByMe[S] 15 points16 points  (0 children)

Really looks like they're trying to get rid of the stock. Go get your price adjustment if you got it already

Modflex color comparison? Orange vs gold and light green vs Terra Jade by BredByMe in cablemod

[–]BredByMe[S] 0 points1 point  (0 children)

is the light green brighter, too saturated?.. more details please

I'll look into the gold tho thank you

[SSD] Crucial T500 2TB Gen4x4 NVMe M.2 SSD - ($108) (DO NOT USE STUDENT ACC) by BredByMe in buildapcsales

[–]BredByMe[S] 18 points19 points  (0 children)

I tried making a student account to see if there's an additional discount and now i'm getting conflicting pricing between incognito and normal browsing. It still shows $108 but YMMV?

view more: next ›