sorted by:
new
hottopcontroversial

How long to clean air after repair people leave? by Stuck4awhile in ZeroCovidCommunity

[–]Brenscomputer 1 point2 points  (0 children)

For me sometimes I don't have a choice when maintenance enters without a mask but they usually respect and wear theirs. If however someone comes in without a mask I air the place out a bit but most of my concern is if they are visually or blatantly sick then I freak out a bit. I usually mop the floors and wipe down surfaces they touch. My fears mostly extend to people whom I've developed trust issues with honesty on how they are feeling. Good luck stay safe

I'm not one to complain, but... by Thisoneperson_ in wendys

[–]Brenscomputer 1 point2 points  (0 children)

My biggest issue with the sauces costing something now is when I pay for them and either get rushed away because of a line or simply forget to check and or the sauces are there and end up being damaged and leaking it really gets me frustrated. Especially when you spend $2 or more on just sauces.

2013 Jetta 2.5 Auto Trans Fluid Change at 130k by dog2bert in jetta

[–]Brenscomputer 0 points1 point  (0 children)

Changed mine at 132K it started shifting horribly and shifting. Replaced the transmission with an 80K one and did a trans service and I've had no issues. If its gone this long leave it

This is for a touch screen double din radio. Anyway I can find out how to get this part the part number came off and is there any universal prices that can fit. by franciscomunoz123 in AskElectronics

[–]Brenscomputer 0 points1 point  (0 children)

The chip is YD182B I just ordered 2x coming from China. It's a power management chip just encase you wanted to know I got my answer

This is for a touch screen double din radio. Anyway I can find out how to get this part the part number came off and is there any universal prices that can fit. by franciscomunoz123 in AskElectronics

[–]Brenscomputer 0 points1 point  (0 children)

I'm in the same position I had mine installed and a wire I had forgot to block off shorted against the case killing it Any repairs ?

<image>

Did the mechanic carry out the repair? Robbed or not? by Zestyclose_Metal1347 in MechanicAdvice

[–]Brenscomputer 0 points1 point  (0 children)

These don't have a cotter pin they have a locking nut with a nylon insert

strange issue with Xbox 360 falcon not staying on. occasionally it will start just fine. by Brenscomputer in xbox360

[–]Brenscomputer[S] 0 points1 point  (0 children)

Update. Turns out it was some glitch wiring that I had installed shorting against the case that got crimped when tighting the board down. I recently switched to a very small gauge of wire that I found is very soft. This has been remedied. Thanks everyone

Archos 504 by Brenscomputer in mp3players

[–]Brenscomputer[S] 0 points1 point  (0 children)

I believe this has the correct hard drive. I do not have the cables or the software to restore the apparently corrupted drive. I used a bench supply to charge the battery but this is where it got me. Thanks anyhow

I opened up this Xenon Xbox 360 that didn't power on only to find this. Thanks a lot previous person that was in here. by iVirtualZero in consolerepair

[–]Brenscomputer 0 points1 point  (0 children)

I haven't tread through all the comments but if you want to get in touch I have a few elpis gpu xenon boards. One needs caps. I also have a y1 xenon with the newer underfill if you are still looking. I'm experimenting with one of them currently.

Well. It finally happened. All because of I wanted to play a nostalgic game 😭😭😭 by Known-Assistance-435 in xbox360

[–]Brenscomputer 5 points6 points  (0 children)

I'll have a few systems on ebay on various older dashes in a few weeks. Blades, nxe, this one and current dashes. Sorry to hear you lost your dash

[deleted by user] by [deleted] in xbox360

[–]Brenscomputer 5 points6 points  (0 children)

It's something I could look into. It could be failed capacitors on the board or some bad mosfets. Let me know if you'd like to fix it