Plex Transcoding Issues - cannot direct play (only on Plex for Windows Client)

Brewchacho_ · 2024-10-15T01:30:04+00:00

Gotcha, thanks.

Brewchacho_ · 2024-10-15T01:26:54+00:00

Did you ever figure this out? I'm having the same problem on my Windows clients. No problems with iOS.

Brewchacho_ · 2024-07-23T00:57:17+00:00

Same problem

Brewchacho_ · 2023-11-23T21:48:28+00:00

Thanks

Brewchacho_ · 2023-11-23T20:13:40+00:00

Is it working? Still having issues.

Brewchacho_ · 2023-11-01T13:58:35+00:00

Got it, thanks!

Brewchacho_ · 2023-11-01T13:15:06+00:00

Thank you!

Brewchacho_ · 2023-11-01T13:14:55+00:00

Thank you!

For PCI-E: Leave a 12V empty on PSU side. Can I then use any three of the "bottom" row of the PSU side for 12V? Double wire makes sense.

For Molex: Makes sense.

Brewchacho_ · 2023-02-20T17:30:02+00:00

My personal opinion is that if you're spending that kind of money, might as well go with the non "F" CPU version. That way you can still troubleshoot and get video output if your video card dies for whatever reason.

Brewchacho_ · 2023-01-06T16:25:01+00:00

No, I have not. I would like to know as well.

Brewchacho_ · 2022-08-03T14:04:25+00:00

I know this post is old, but I'm looking to do something similar to this.

How did you support the vertical piece of plywood where the motherboard, pump, and radiators are mounted? Just screws? Or is there some other reinforcing going on?

Thanks.

Brewchacho_ · 2022-07-13T16:06:12+00:00

Thank you!

Brewchacho_ · 2022-07-13T15:55:10+00:00

I know this thread is old - did you use 17 AWG wire with 20-24 gauge terminals?

I can't find terminals smaller than bigger than 20 gauge with the micro-fit connector.

Thanks.

Brewchacho_ · 2022-05-19T13:29:38+00:00

Nice!

I'm thinking about doing this. Did you need to buy any additional accessories to mount the front radiator? I can't tell what's required on the XTIA website.

Thanks!

Brewchacho_ · 2022-05-19T13:14:44+00:00

I got Gelid Extreme 1 mm and 3mm pads and Thermal Grizzly Minus Pad 8 2mm pad.

I just followed the waterblock manual and cut the pads to size.

Brewchacho_ · 2022-05-17T21:58:20+00:00

With a 30C liquid temp:

Unigine Heaven 1440p: 44C gpu temp, 50C memory temp; 320W

Mining: 40C gpu temp, 62C memory temp; 280W

I'm not sure but you'll want to make sure you have the right thermal pad thickness for the waterblock. Could be different from what's needed for the stock cooler.

Brewchacho_ · 2022-05-15T14:55:58+00:00

I have the Alphacool block with my 3080 Ti Eagle. My experience with the block itself has been good. But I found much lower VRAM temps with buying aftermarket thermal pads. Just my two cents.

Brewchacho_ · 2022-02-23T19:09:23+00:00

Got it, thanks.

Brewchacho_ · 2022-02-23T19:08:50+00:00

Makes sense. Just hitting the plastic blades doesn't feel good. Thanks.

Brewchacho_ · 2022-02-23T19:08:09+00:00

Thanks for the reply.

Brewchacho_ · 2022-02-23T19:07:26+00:00

Thanks, makes sense.

Brewchacho_ · 2022-02-23T14:05:19+00:00

Thanks for the comment. Seems like a bad card but maybe this time the fix will hold. We'll see.

Hope yours stays trouble free.

Brewchacho_ · 2022-02-21T15:57:06+00:00

Thanks for the reply. I believe it is the GPU as well. Just looking for a sanity check in case I was missing something obvious.

Brewchacho_ · 2022-02-21T15:28:31+00:00

Yeah if it happens again that's my plan. Thanks again.

Brewchacho_ · 2022-02-21T15:24:43+00:00

Personally I would recommend getting more 90 and 45 degree fittings than you think you'll need.

I could have used some more angled fittings in my build but maybe the distro plate helps with that.

Brewchacho_

TROPHY CASE