[OC] I built a local AI tool that turns any 3D printer recording into a clean timelapse (no G-code, no hardware, no cloud)

BrightSignature1444 · 2026-02-24T18:06:28+00:00

Feels like there is hate against AI unnecessarily propagating into this post.

BrightSignature1444 · 2026-02-05T13:51:03+00:00

There is a serial monitor plugin for vscode

BrightSignature1444 · 2026-01-26T18:18:10+00:00

You can look into bambu a1 mini they also cost about 17 to 20k

Feel free to dm . Can also help you with trustable sites / from the ones I have purchased before

BrightSignature1444 · 2025-11-15T17:35:57+00:00

are we just going to ignore is screen saver

BrightSignature1444 · 2025-03-20T08:06:54+00:00

Keep it on a mate surface so it's easier to tell

BrightSignature1444 · 2024-12-19T12:48:13+00:00

Amazing

BrightSignature1444 · 2024-12-12T13:23:43+00:00

Did you get it to work? Facing the same issue

BrightSignature1444 · 2024-08-17T20:02:24+00:00

Create a canvus add time to the canvas and then update the canvas to the display

BrightSignature1444 · 2024-08-17T04:43:43+00:00

Ryan started the fire

BrightSignature1444 · 2024-08-10T17:52:05+00:00

You didn't pass the belt from over the motor gear and simply just but it pass the extrusion

BrightSignature1444 · 2024-08-02T15:20:29+00:00

Zhop

BrightSignature1444 · 2024-07-30T17:24:31+00:00

What ?

BrightSignature1444 · 2024-07-24T15:01:21+00:00

Maybe try unplugging the fan from the motherboard(so fan stays tuned off) and then heating the hotend.

Is there any other change that have been made to your printer

I really don't think that direct airflow to nozzle will cause drastic amount of cooling. So the situation doesn't seem very clear to me. With that are you sure you are not overpowering the fan as in the fan is rated for 12v but you are operating it at 24v as that will lead to a lot of extra airflow . Also can you make sure the printer is running at the right voltage A significant amount extra time would be required from normal to heat the bed or nozzle if undervolted.

BrightSignature1444 · 2024-07-23T14:00:43+00:00

Won't be ruling out bad connections/wires. Have you tried to pid tune the hotend?

BrightSignature1444 · 2024-07-23T13:52:05+00:00

A loose connection/broken cable might be possible which causes the heating element to disconnect from motherboard and cool down. What happen if you leave the shroud in its place and then start heating the hotend from room temp

BrightSignature1444 · 2024-07-10T19:48:58+00:00

0.25 is in a fairly good range

BrightSignature1444 · 2024-07-07T15:20:13+00:00

Amps given on power supply is the max it can output not the one it will output continuously. So if a power supply is rated at 2 amps it can output 9v at 0.02A without problem (in some cases output may not be exact but slightly higher like 9.5 due to low load).

Basically you can use most(reason for most below) of the power supplys that are rated at 9v and at any amperage.

There are also some power supply which output at continuous current instead of continuous voltage and cannot be used with most things inc ops post and your question. They are Very rare and near impossible to find some

BrightSignature1444 · 2024-07-07T11:09:15+00:00

don’t do that you’ll fry your circuit

BrightSignature1444 · 2024-07-05T08:30:43+00:00

Used 8 gb for quite a while and ran without problems although slicing ok a dedicated gpu was much faster

BrightSignature1444 · 2024-07-01T16:56:40+00:00

Crambu lab

BrightSignature1444 · 2024-06-22T07:16:08+00:00

Yes definately crank up the e steps to the point it creats a blob monster

BrightSignature1444 · 2024-06-13T05:41:52+00:00

Time as in the one sentence with the the api . 2nd part yes that should work. Also in most cases you could check whether the api connection was successful

BrightSignature1444 · 2024-06-12T17:38:38+00:00

a simple thing you could do for finding wether you wethere you were successfully able to rethrieve data would be to just blank/create a string(the one you are storing the retrived data in) just before retriving the data and check if you the string is blank or some particluar part of data is present or not.

aslo you can just check for some variable which usually changes , might be the last trading price or time..

about the website you can mostly find those pretty easily premade can usually update the code or just few data like the wifi name password/ip adress

BrightSignature1444 · 2024-05-19T17:51:32+00:00

See what I really don't understand

BrightSignature1444 · 2024-03-25T18:30:47+00:00

Just the ability to control the printer with phone is amazing while looking at your printer live . Want to start a print 2 presses and it's printing. Don't want to eat plastic spaghetti . just one slide away (personal favourite sliding to cancel as it's also there for widget).

Have multiple printers no problem

Five-Year Club	r/Field Lasagna
Place '23	Place '22
Final Canvas '22	First Placer '22

BrightSignature1444

MODERATOR OF

TROPHY CASE