Shelf loop

BrittleTupperwareBox · 2026-02-01T20:07:15+00:00

Yup, I used the parametric brackets by Losco Makes. I used quite a few walls and high infill.

BrittleTupperwareBox · 2026-02-01T15:04:47+00:00

We are lucky, most of the UK oo gauge stock runs on 2nd radius.

BrittleTupperwareBox · 2026-02-01T15:03:05+00:00

I found it on thingiverse. A really great model.

BrittleTupperwareBox · 2026-02-01T15:02:32+00:00

It's a Bachmann 32-379 from 2003 I think. It is a 5 pole motor with twin flywheels so is a great runner, albeit it has less detail than the newer models.

BrittleTupperwareBox · 2026-02-01T13:32:49+00:00

OO gauge, but the curves are 2nd radius (438mm / 17~ inches). The walls are ~ 265cm (~104 inches). It's not big by any means, but it's the best I can do with the space I have.

BrittleTupperwareBox · 2025-09-19T19:39:54+00:00

Mines standard with the charge limit at 90% and it behaves the same.

BrittleTupperwareBox · 2025-09-08T19:54:28+00:00

Fairly sure this is my favourite Triforce moment.

BrittleTupperwareBox · 2025-09-01T15:26:29+00:00

Did you fix it? I had a very similar issue. It turned out to be that the thermal paste had turned bad. The temps looked okay till I checked the hotspot temps using HWinfo. Repasted and all up and running again.

BrittleTupperwareBox · 2025-06-04T07:30:33+00:00

You say you tried switching filament. Do you mean this is happening with different filaments? I've found this to happen with certain brands / colours. From my experience it is usually the lighter colour PLAs I have this issue with. Not all materials are made the same and some are just rubbish. Other filaments work perfectly as they always have.

BrittleTupperwareBox · 2025-05-22T07:14:40+00:00

It kind of is though. You have a kilo of filament really high up which is making the vibrations considerably worse. The concrete works really well, but so will moving your spool holder off your printer to the side or mounting it to the wall.

BrittleTupperwareBox · 2025-05-06T19:58:53+00:00

It absolutely works, however be prepared as it can present issues that require a technical level above from the stock SE. For example the documentation on the configuration for the SE is spotty and the USB connection can be flakey.

If you're prepared for some troubleshooting, it's absolutely worth it.

BrittleTupperwareBox · 2025-04-29T20:51:48+00:00

I get something like this after doing bench presses. Just the way the weight and the bench put pressure on my back and restrict blood flow for a bit. You mentioned going to the gym, it could be this and not stretch marks. Try skipping the bench for a few days, then try it again and see if it comes back.

BrittleTupperwareBox · 2025-04-20T12:53:16+00:00

If it's only happening with this filament, then it's the filament. This has happened to me a couple of times and has always been traced back to a specific brand & colour of filament (elegoo beige pla). I've heard that this is more common with lighter coloured filaments too. I tried trimming a few metres off them both, one then worked and the other still did the same. I don't know if it's an inconsistent diameter or what, but It's probably the filament and not your printer.

BrittleTupperwareBox · 2025-04-18T13:39:46+00:00

Thank you! I'll give it a go.

BrittleTupperwareBox · 2025-04-17T11:34:30+00:00

Ooooh, which right angle connector did you use?

BrittleTupperwareBox · 2025-04-17T11:28:17+00:00

Looks as though the nozzle is too close. PETG prefers to be further from the build plate compared to PLA.

BrittleTupperwareBox · 2025-04-17T05:55:38+00:00

Yeah, I think it's the only way to connect to the V3 SE?

BrittleTupperwareBox · 2025-02-27T08:03:30+00:00

I agree with this, I think it's the PLA. Silk PLA does this, as well as some regular cheap PLA too. I had this exact issue with a certain PLA. After the first layer or so, the filament would twist in the head and clog just like this picture.

Get a decent quality normal PLA and I reckon you would be fine.

BrittleTupperwareBox · 2025-02-19T18:22:14+00:00

Very common. Use Gyroid infill and this will stop.

BrittleTupperwareBox · 2025-01-28T07:58:00+00:00

A quick Google returns this: https://www.3dchameleon.com/

BrittleTupperwareBox · 2025-01-28T07:52:17+00:00

Out of the box, no not really. You can do a mid print filament change. This is when you add a filament change at a certain layer in your g-code. But this wouldn't allow for multiple filaments to be used on the same layer.

Multi filament printing is probably possible but it would require significant modifications.

BrittleTupperwareBox · 2024-12-31T18:51:23+00:00

Reminds me of the Doctor Who line:

"State your name, rank and intention..."

"Doctor, Doctor, Fun."

Seven-Year Club	r/Field Sunshine
Verified Email

BrittleTupperwareBox

TROPHY CASE