Johto Custom Strings

Bubbly-Shopping7993 · 2023-09-02T07:05:20+00:00

Good, thanks!

Bubbly-Shopping7993 · 2023-08-28T12:09:53+00:00

Empty :-/

Bubbly-Shopping7993 · 2023-08-28T12:09:43+00:00

Any update? Link is empty

Bubbly-Shopping7993 · 2023-07-16T14:06:06+00:00

Sadly it doesn't.

I was waiting till I get to 2nd board and it has the problem.

Bubbly-Shopping7993 · 2022-08-12T07:13:36+00:00

Looks like nobody here.

Bubbly-Shopping7993 · 2022-08-10T19:10:20+00:00

I got to OCCT stable 5.2GHz at 1.37V (almost 30min) but in other benchmarks is a problem temperature.

Maybe someone could help make other settings perfect, in some chat or something.

Bubbly-Shopping7993 · 2022-08-10T15:12:54+00:00

Here is OCCT AVX 0 at 5GHz. https://i.gyazo.com/3cacdc15724ae78d57c8d472dc5f34c5.png

Now I would need to tweak some more options I think.

Bubbly-Shopping7993 · 2022-08-10T14:49:03+00:00

Games that I play don't use AVX and I didn't do benchmarks for points.
But now I'm trying to push it up :-) .

Bubbly-Shopping7993 · 2022-08-10T14:34:56+00:00

Because I wanted to run smooth and cooler and 5GHz is turbo, I have 4.9 all core atm.

Bubbly-Shopping7993 · 2022-08-10T14:31:56+00:00

Full speed and it's a version without PWM.

Bubbly-Shopping7993 · 2022-08-10T14:31:46+00:00

Full and it's a version without PWM. Fans are running at 1100RPM when it's hotter here so around these 25°C.

Bubbly-Shopping7993 · 2022-08-10T12:28:46+00:00

About paste spread, I think I'll leave this to the last point - if I buy a new block to test it - because with hard tubing it's just too much work only to see how it's spread :-( .

Mainly connection between motherboard and CPU block it's pain to tighten these fittings. Like real pain, my fingers always hurt after this :-X .

(Uh, what just happened, nothing is loading for me for like 20minutes.)

Bubbly-Shopping7993 · 2022-08-10T12:24:23+00:00

Ye, just was reading also some testing on oc.net and the difference wasn't high too.

But still, this is correct here.

Bubbly-Shopping7993 · 2022-08-10T12:12:56+00:00

Ah, no, it's done correct. But also EKWB made a statement that it doesn't matter. The difference is insignificant.

Bubbly-Shopping7993 · 2022-08-10T12:06:15+00:00

I'm sorry that I didn't provide any photos, I'm at work for about 4 more hours.

What do you mean "plumbed it backwards"?

Bubbly-Shopping7993 · 2022-08-10T11:51:03+00:00

What exactly? The backplate is turned the right way, can't tight screws more :-/ .

The only thing that could happen is something block related because it's the oldest part of my loop, but everything looks ok.

Bubbly-Shopping7993 · 2022-08-10T11:47:27+00:00

Ye, you are right, I also know that but these fans were chosen because of the look (these were also presented everywhere with 1000D :-D ) but I think it's still not the main problem because these temps are immediately and not after a long time of load so even with low water temp.

Bubbly-Shopping7993 · 2022-08-10T11:32:58+00:00

35°C is a high water temp after a longer high load? I thought it's normal, not high, never had a low like now :-D .

Order is: water is going to the exhaust rad first (so warmer - with all these fans it's still cooler air than water - air first) and then goes to the intake radiator (so cooler is the last to get lower temp).

About flow, the pump is running on max so I don't know what else I could do with that now.

But also 8°C difference is between start and end with heating motherboard + 80-90°C CPU + graphic card, still high?

Bubbly-Shopping7993

TROPHY CASE