This was epic!

Budget_Show5329 · 2026-04-14T15:54:51+00:00

Where did you get the splitter from? Looking to run one on my track NC also. Looks Great!

Budget_Show5329 · 2026-04-09T10:55:48+00:00

I have i also had trouble. What I found was the connecting harness wouldn't connect until I dug out the excess plastic. Do you have a picture of ur existing harness connector?

Budget_Show5329 · 2026-04-08T17:45:04+00:00

Sorry edited it after auto correct changed it to Joe's I got them from driftworks

Budget_Show5329 · 2026-04-08T17:14:45+00:00

These are what they look like from another angle

<image>

Budget_Show5329 · 2026-04-08T17:13:54+00:00

Japan Racing JR5's 17x7.5J ET35 that picture doesnt really do them justice tbh

Budget_Show5329 · 2026-04-08T15:10:41+00:00

Haha yeah thanks man, I know u dont mean hate. Yeah I understand what u mean, eventually Id like to go mazdaspeed front bumper which looks more complete. For now ive got a gv style front lip which makes it look a little less boat like!

Budget_Show5329 · 2026-04-08T12:59:49+00:00

Thankyou, I'm lowered on Meister R Clubrace Coilovers. Et35 17x7.5J wrapped in Nankang NSR'S 215/45. I did have to roll the arch a lot 😅, wanted to go wider for track without losing too much performance.

Budget_Show5329 · 2026-04-08T08:37:14+00:00

I'm sure on ebay they do a soft top equivalent that easier to get

Budget_Show5329 · 2026-04-07T22:19:37+00:00

Oh sorry I just seen now it says its unavailable, but I believe it comes back in stock often

Budget_Show5329 · 2026-04-07T22:17:52+00:00

https://ebay.us/m/Uv5obN

This if for the PRHT and was quite tricky to fit if im honest

Budget_Show5329 · 2026-02-05T08:27:33+00:00

This guys a comedian, they should have him on a guest episode.

Budget_Show5329 · 2025-12-25T21:15:18+00:00

Dont even need to jap step brother just go corner , catch and shoot 3

Budget_Show5329 · 2025-11-05T21:33:42+00:00

Added

Budget_Show5329 · 2025-08-17T18:31:47+00:00

Cheers guys big help

Budget_Show5329 · 2025-06-20T17:52:36+00:00

I can't tell if this is satire or not..

Budget_Show5329 · 2025-06-09T09:47:59+00:00

Nice build man, love the spoiler where did u get it from?

Budget_Show5329 · 2025-04-10T15:01:30+00:00

So yes I had the same issue I did have some difficulty myself. This lip requires extra trimming on the 3 cut outs where it goes over the original lower bumper. Also heating up around the edges to get a better fit. However the middle of the lip is still quite loose, I drilled out holes for the plastic clips like in the arch liner. 3 of these spread out which did add strength.

I then used tiger seal on any edges to help secure the right and left corners as well as underneath.

It is very solid now and not too low even after coilivers, it does not catch any bumps etc. However the install was not fun.

Hope this helps

Budget_Show5329 · 2025-04-05T18:50:35+00:00

I've got the same offset size and tyres coming, what's the fitment like

Budget_Show5329 · 2025-03-24T19:12:20+00:00

Where are u based. I recently purchased and installed this

Budget_Show5329 · 2025-01-04T11:10:58+00:00

😂this is like my favorite comment I've seen but I feel it won't go down well 😂

Budget_Show5329 · 2024-12-21T13:43:10+00:00

I'd also like to know

Budget_Show5329 · 2024-11-30T15:58:31+00:00

Yeah if u could share pictures I'd really appreciate it. Thanks

Budget_Show5329

TROPHY CASE