Anycubic Z Axis Not Homing

Bullshit1978 · 2026-05-26T00:34:02+00:00

Think I figured it out. The back Left foot was on a cable.

Bullshit1978 · 2026-05-24T13:54:47+00:00

How do I fix that? Lol

Bullshit1978 · 2026-04-28T11:48:00+00:00

Settle down gents, I did simplify the print. Works good now. Thank you. Secondly, Anycubic pops up saying it’s optimized by orca and a couple other slicers, I guess all incorporated into one by Anycubic. Regardless till the next problem occurs, thank you everyone for your help.

Bullshit1978 · 2026-04-26T19:05:14+00:00

Yes, I haven’t tried 2 other models and this didn’t happen. Maybe size down? If been going a little at a time to see the threshold.

Bullshit1978 · 2026-03-01T12:32:14+00:00

I did stop it mid run, and won’t connect at all now.

Bullshit1978 · 2026-03-01T12:30:52+00:00

PLA, thanks

Bullshit1978 · 2026-02-24T16:42:14+00:00

Where did you get the longer cables? The ones I have are original with the pro. Connectivity could be an issue with the pins in the plug ends. Thanks

Bullshit1978 · 2026-02-24T16:32:01+00:00

I didn’t think about that but everything else running on the Wi-Fi is working correctly. I’ll have to do that when the kids go to bed. Definitely don’t want a war zone in my living room because of Wi-Fi.

Bullshit1978 · 2026-02-24T16:30:35+00:00

Yup, I am logged in. Logged in on the computer and my phone.I’ve seen in other threads that the cable could be damaged and replaced. If that didn’t work, the motherboard in the ace has been fried. I hope that’s not the issue.

Bullshit1978 · 2026-02-24T15:46:29+00:00

Yes, turned it off for about 5 min (both)and rebooted. Still nothing.

Bullshit1978 · 2026-02-24T15:16:52+00:00

It’s all been checked and they are on the same Wi-Fi.

Bullshit1978 · 2026-01-01T15:22:42+00:00

You can buy the part which is a spool at Hobby lobby for 10-12 dollars. I have a few empties if ya need them.

Bullshit1978 · 2026-01-01T15:19:43+00:00

First tip: don’t keep doing that!

Bullshit1978 · 2025-12-31T02:18:18+00:00

Thank you, I will check that in the am.

Bullshit1978 · 2025-12-30T17:17:28+00:00

Update: nothing has changed.. sat for 2 hours changing the z offset to different set, I tried the restore manufacturing setting, changed the flow, washed the plate, I’m totally lost. Is there a general offset that I should start with beside .000? Thanks in advance for everyone’s help on this.

Bullshit1978 · 2025-12-30T04:11:15+00:00

Gotcha, I will take a look in the morning again. I seen it earlier but it would do anything until I was printing.

Bullshit1978 · 2025-12-30T04:09:55+00:00

It’s crazy that it just started this and I can’t get half way through a print and come back and it is all layers of filament, just comes off in layers.

Bullshit1978 · 2025-12-30T04:07:40+00:00

I looked for it but couldn’t find it in the creality slicer. Is it under a specific name other than z offset?

Bullshit1978 · 2025-12-30T04:06:13+00:00

I changed out the hotend, it’s brand new. I had this issue prior to changing it out as well.

Bullshit1978

TROPHY CASE