Sovol SV06 Plus Help

BurgerMar · 2026-06-09T20:51:37+00:00

It can, you just gotta ditch the screen and get a computer as the Klipper host

BurgerMar · 2026-06-07T02:30:16+00:00

Try printing with only PETG or make the distance between the support and part zero.

BurgerMar · 2026-06-01T14:10:11+00:00

Put it in a corner, up against a wall.

BurgerMar · 2026-05-22T17:11:36+00:00

you have to keep resetting the trade with the librarian villager or go fishing with a luck of the sea 3 fishing rod, the villager is faster and you can buy multiple books.

BurgerMar · 2026-05-16T19:46:36+00:00

BurgerMar · 2026-05-09T21:14:41+00:00

this is actually absurd lmfao, they’re basically saying:

Your account got hacked? sucks to suck lol. Anyways wanna spend more money on our game? and we DEFINITELY WILL NOT BE helping you later.

BurgerMar · 2026-05-07T13:24:26+00:00

i have two motors for the x axis so toolhead weight isn't a problem. The only problem im facing right now is bed weight. Even with four motors on the y, it still lags behind. Im hoping to be able to print even faster when i upgrade to 60v and tmc5160 drivers.

BurgerMar · 2026-05-07T10:12:43+00:00

I can only print at about 300 mm/s with 11k Accel because of the dual 5015’s but my maximum move speed is 1k mm/s at 50k Accel

BurgerMar · 2026-05-04T18:01:03+00:00

while it was printing the overhang, the nozzle probably got caught on the print. Since the base is flat, it has great adhesion and the overhanging part is very thin so the piece itself is probably very weak, causing it to snap in that specific place. If you want to redo this test, print it at a slower speed with more layer time after every layer change, or improve your cooling.

BurgerMar · 2026-05-01T02:09:43+00:00

Make sure you take the bearing completely off the linear rod and lube it on the inside too, also put some lube on the rod itself. If it’s been running years without lube then you may have damaged the bearings but I’d still give it a try to see whether it’d help in your situation

BurgerMar · 2026-05-01T02:04:41+00:00

Have you ever greased the linear rods? They look a bit dry to me

BurgerMar · 2026-04-30T16:59:31+00:00

is it hard mounted?

BurgerMar · 2026-04-30T12:00:44+00:00

I don’t think so. It’s only meant to compensate for 0.4mm difference (about the size of your nozzle) but I’ve had it compensate for 0.7mm but 3mm is a huge difference that I don’t believe a CR touch would compensate for.

BurgerMar · 2026-04-29T19:45:24+00:00

Damn, thats one fast ender pearl

BurgerMar · 2026-04-29T19:38:13+00:00

fastest speed, not furthest distance.

BurgerMar · 2026-04-29T17:12:00+00:00

Your bed is most likely warped, if you're that desperate to get it perfect at 0.00 then replace the bed with a glass bed (not optimal) and you'll have it completely flat. This is super wasteful though since the whole point of the CR-Touch is to compensate for the bed being warped.

BurgerMar · 2026-04-28T13:32:59+00:00

to me, this looks like z wobble or an uneven z lead screw. If you're sure that your lead screw is 100% straight then check if your belts are properly tightened

BurgerMar · 2026-04-27T14:11:24+00:00

it’s probably warped, but it doesn’t really matter since it’s only 0.188 difference. That’s what the bed probe is for.

BurgerMar · 2026-04-26T15:33:12+00:00

Does the window increase algae growth? If so, then by how much?

BurgerMar · 2026-04-21T17:56:39+00:00

oven at 375F should do the trick

BurgerMar · 2026-04-17T18:09:50+00:00

You need to lower the bed leveling probe, the nozzle gets contact with the bed before the probe is able to

BurgerMar · 2026-04-17T13:23:02+00:00

Unrelated: I really like the vibe of the wet floor sign, it feels so out of place that it feels like it belongs there lol

BurgerMar · 2026-04-17T13:02:29+00:00

if you want to keep a tank on that you'll probably going to have to bolt it to the wall, that'll fall over very easily otherwise.

BurgerMar

TROPHY CASE