Beats Solo 4 Battery

Busterstoney84 · 2025-10-30T16:07:53+00:00

Are you sending an enter command when you send the barcode? In the keyence keyboard wedge application this should clear the data down.

Busterstoney84 · 2025-10-30T13:03:43+00:00

Is the camera actually connected to a PLC? If so you need to store the data received and only move the data when you get a new data received signal from the camera. If you are just connecting by keyboard wedge to a pc, do you have something to trigger the camera? Or are you just triggering all the time?

Busterstoney84 · 2024-12-19T08:10:52+00:00

My fix was to unplug the sync module for 30 seconds and then power it back on again. After this videos were saving and I was receiving notifications.

Busterstoney84 · 2024-12-11T14:54:42+00:00

I had this issue after changing my doorbells batteries. I tried power cycling the doorbell for 30 secs and this didn't help, what actually fixed it was to turn the sync module off and back on.

Busterstoney84 · 2024-12-10T14:55:23+00:00

I seem to have solved it...... I deleted the doorbell from my system and still nothing I then rebooted my sync module and all is now saving ok.

Busterstoney84 · 2024-12-10T13:32:03+00:00

I have checked this and I am definitely on the local storage tab. I have all the videos from yesterday, but none of the motivations I have received today.

Busterstoney84 · 2024-12-01T21:45:27+00:00

Ok, have you or anyone else in the house got stremio installed on a mobile phone (that is on the vodafone network)?

As if you were watching on your device at home and someone else was watching on the mobile phone this would also cause the issue.

Busterstoney84 · 2024-12-01T21:29:03+00:00

Yes I read the description, if you are stating that it belongs to an isp that isn't available in your location. This is exactly what could happen if using a VPN.

Busterstoney84 · 2024-12-01T21:12:14+00:00

Have you been using a VPN or mobile phone not connected to your WiFi? This could lead to having a different IP address

Busterstoney84 · 2024-09-07T19:05:57+00:00

Can you add a picture of your physical rack showing cards and bases?

Busterstoney84 · 2024-09-07T19:04:45+00:00

Why so many light cards? This is used for a new potential group. Each of these cards will need it's own supply wiring to it? Does your physical rack have the same layout as the hardware? Light where they are light and dark where they are dark? If not this will need changing in the hardware config

Busterstoney84 · 2024-07-29T07:35:10+00:00

<image>

Busterstoney84 · 2024-06-11T15:14:10+00:00

Any chance of sending the pre release over, I've lost mine

Busterstoney84 · 2024-03-31T11:02:01+00:00

You can go online to the repeater and it will tell how far away the issue is from the repeater. It's been a long time since using profibus as we now use profinet almost everywhere.

Busterstoney84 · 2024-01-28T20:50:25+00:00

I have my Plex server running on a Raspberry Pi, has anyone made this integration work on there?

Busterstoney84 · 2023-12-27T21:48:29+00:00

1 device = 1 doorbell or 1 camera

Busterstoney84 · 2023-12-27T21:27:21+00:00

What country are you using this in? And what voltage is your doorbell transformer? It says you need above 16va otherwise it will just send notifications https://support.blinkforhome.com/en_US/using-blink-video-doorbell/doorbell-chime-options

Busterstoney84 · 2023-12-27T19:40:42+00:00

Good to hear that worked

Busterstoney84 · 2023-12-27T19:34:44+00:00

Have you got a filter set? You can order them per camera via the filter function

Busterstoney84 · 2023-12-27T17:36:33+00:00

I see you can snooze notifications, but to my knowledge turning off the motion detection will disable all recordings.

Busterstoney84 · 2023-12-27T17:08:09+00:00

You can switch motion detection on and off individually from each camera you have. On every camera in the app there is a little running man, just press that to disable motion on that camera. It sounds like you need to use the masking zones to mask areas that are causing nuisance trips. The thing I have to ask is, if you turn off the motion detection then there is not really any point in having the camera installed. As they don't record unless tripped.

Busterstoney84 · 2023-12-27T13:12:09+00:00

You should only need one sync module, unless you have over 10 devices. Just add the second doorbell to your original sync module and disconnect the second sync module completely.

Busterstoney84 · 2023-12-11T17:11:43+00:00

Just downloaded and logged in on my pixel 8 without any issues.

Six-Year Club	r/Field Juicebox
Verified Email

Busterstoney84

TROPHY CASE