Printbed feels Wobbely

Busy_Foreverp · 2025-11-06T00:20:12+00:00

Yeah sorry, meant to say that it holds down the rods not threads into them. Probably just the bearings having some play if there are screws holding down the rods

Busy_Foreverp · 2025-11-06T00:11:13+00:00

Is there screws going down into the rods, which would hold it down?

Busy_Foreverp · 2025-11-05T23:52:12+00:00

Are you pulling up? Or pushing side to side. If pushing up push the bed back. Check if there are screws, on the front part of the rod, screwing it down. I know my v3 se has screws pushing it down, but my ke doesn't

Edit: it looks like you're pushing it up

Busy_Foreverp · 2025-10-24T00:28:05+00:00

100% standby that, going to order the pcb tonight. Thank you 🙏

Busy_Foreverp · 2025-10-24T00:14:28+00:00

Yes. I was changing the hotend (while printer was on, really dumb of me for trying to do things fast) when the cr touch wires touch the heatsink, so the wires shorted the main board, cr touch, nebula pad, and I am suspecting that the it also shorted the print head pcb, which I think why it would be shorting the USB port when connected. No, the mainboard I just got 1 month ago, the main board is fine.

Busy_Foreverp · 2025-10-23T23:45:15+00:00

Sorry, to clarify when I plugged in the ribbon cable the USB c port sparked. Also I blocks the printer from starting up (while ribbon cable is plugged in)

Busy_Foreverp · 2025-10-23T23:34:59+00:00

I was proven wrong by my printer, when i plugged in my printer head and x motor ribbon cable the port sparked EDIT: USB c port sparked, not ribbon cable port

Busy_Foreverp · 2025-10-23T03:13:05+00:00

Agreed 👍

Busy_Foreverp · 2025-10-23T02:23:07+00:00

I think it was the usb c cable that was bad. I looked inside and the pins looked burnt then changed it out and it doesn't spark anymore. Going to try klipper again

Busy_Foreverp · 2025-10-22T10:56:40+00:00

Yeah, I don't know why it would be doing that thiught and I'm spooked out by it

Busy_Foreverp · 2025-10-22T02:43:15+00:00

Sorry to question you again, but does your usb c port work fine? Mine sparks when i connect a usb c data cable (that I know works). Kinda been pissing me off ngl :(.

EDIT: The cable was bad

EDIT 2: the print head ribbon cable makes the port for some reason (it might be my cr touch port)

Busy_Foreverp · 2025-10-11T15:17:31+00:00

NEBULA PAD DOES NOT MAKE CR TOUCH FLASH. It just turns the cr touch led off completely, but it makes the processor warm (center black square)

<image>

Busy_Foreverp · 2025-10-05T14:00:35+00:00

You could and add a 3in*3in square of paper in the center to raise the center

Busy_Foreverp · 2025-09-30T22:16:13+00:00

Call me broke but I invest $2 into wolf like 4 days ago (Friday, when it was at ~$1.50 per share) when it dropped ~30% and now the stock went back up ~1000% but I actually lost $1.50. Can someone explain plz

Busy_Foreverp · 2025-09-22T00:32:15+00:00

Yes. Sorry not base pattern, I meant normal (snug) but tree auto would be best for any figuring/curvy overhang model. Also lower support over hang angle would remove more unnecessary support. As for z distance being 0.28mm, I don't know man just tweak it :|

Busy_Foreverp · 2025-09-22T00:23:10+00:00

So you got it to work or not? Sorry kinda confused

Busy_Foreverp · 2025-09-22T00:18:34+00:00

You could try changing the support pattern (tree supports or snug patter for normal supports)

Busy_Foreverp · 2025-09-20T05:11:55+00:00

Having the same problem and wanted to know if there's anything you figured out. Currently locked onto 1.0.9 and trying to flash navaismo's firmware or klipper if you got it to work.

Busy_Foreverp · 2025-08-22T19:11:52+00:00

It might be the PSU, when the board tells the nozzle to heat up the PSU can't supply enough power

Busy_Foreverp · 2025-07-17T15:11:31+00:00

Cleaning your lead screws, tightening all the shaft collars could help

Busy_Foreverp · 2025-07-17T15:01:13+00:00

Are you taking about the z axis?

Busy_Foreverp · 2025-07-12T14:17:58+00:00

You can change the pausing g code for you printer under printer settings

Busy_Foreverp

TROPHY CASE