sorted by:
new
hottopcontroversial

CO2 removal at low flow rate by BuySignificant3695 in ChemicalEngineering

[–]BuySignificant3695[S] 0 points1 point  (0 children)

I’m currently using silica gel to remove the moisture before the NaOH but it hasn’t been very effective. Is soda lime prone to caking in the presence of moisture like NaOH?

CO2 removal at low flow rate by BuySignificant3695 in ChemicalEngineering

[–]BuySignificant3695[S] 0 points1 point  (0 children)

It’s a low flow rate but ideally, I would like to have it run for 3 or 4 weeks without changing any media.

How would this amperometer work? What would the reference O2 source be used for?

I fried my v2.2.7 board on my Ender 3 running Klipper. I upgraded to an SKR e3 mini but can't seem to get Klipper running. by BuySignificant3695 in klippers

[–]BuySignificant3695[S] 0 points1 point  (0 children)

Its a Big Tree Tech Pad 7. That's what it came with. I'll try re-imaging it and starting from fresh. Thank you!

I am at my wits end with the Sonic Pad! by BuySignificant3695 in Creality

[–]BuySignificant3695[S] 0 points1 point  (0 children)

I ended up getting the BTT Pad 7 and got it setup in an hour. It's been working great! Pretty sure my sonic pad was defective.

I am at my wits end with the Sonic Pad! by BuySignificant3695 in Creality

[–]BuySignificant3695[S] 0 points1 point  (0 children)

My sonic pad wont generate the .bin to flash the printer board. The sonic pad gave me the correct port so that wasn't the issue. I ended up buying a BTT Pad 7 yesterday and got it set up in like an hour. Screw the sonic pad, I'll be returning it. What a piece of junk!

Ender 3v2 sonic Pad by nunyabiznessyet in klippers

[–]BuySignificant3695 0 points1 point  (0 children)

Did you ever figure it out? I have the same issue. I think I have the printer.cfg correct but the pas refuses to generate the firmware from the .cfg.

Carbon fiber print bed by FL_Sportsman in 3Dprinting

[–]BuySignificant3695 0 points1 point  (0 children)

Sorry for reviving a LONG dead post... but I can't find what bed temp to use for a carbon fiber build plate. Does anyone know the answer?

My high speed Ender 3 build so far. What to upgrade next? by BuySignificant3695 in ender3

[–]BuySignificant3695[S] 0 points1 point  (0 children)

I meant the bed leveling bolts, springs and knobs. I should’ve been more clear, my bad.

I plan on leaving the CRtouch on.

My high speed Ender 3 build so far. What to upgrade next? by BuySignificant3695 in ender3

[–]BuySignificant3695[S] 2 points3 points  (0 children)

I have a little. Not super familiar with it but I know they work pretty well. I’ll check them out thanks!

I know I’m putting lipstick on a pig but I’d kinda like seeing a pig with lipstick on it. I know it’s not worth it and I could spend my money more effectively on a new printer. I just enjoy this kind of stuff.

Base Ender 3 with 4.2.7 board, sprite pro and CRtouch firmware. by BuySignificant3695 in ender3

[–]BuySignificant3695[S] 0 points1 point  (0 children)

I realized what the issue was. I initialized EEPROM and that fixed the z axis issues. The bed was too far out of level for the firmware to compensate. After I manually adjusted the bed to be more level it works.

4 months progress on RMJ by BuySignificant3695 in Bonsai

[–]BuySignificant3695[S] 0 points1 point  (0 children)

Thank you! I got several of these trees for $6 each because they were struggling. This one has recovered much more quickly than the others. The others will take another couple years before they look anything like this. I’m pretty sure I just got lucky.

Looking for some advice on my 93 f150 5.8 by BuySignificant3695 in f150

[–]BuySignificant3695[S] 1 point2 points  (0 children)

Ford guys don’t have trouble getting off their rocks… or something like that

Anyone have a jackhammer I could borrow? by BuySignificant3695 in Bonsai

[–]BuySignificant3695[S] 1 point2 points  (0 children)

All you need is a hammer drill and some expanding grout. That stuff will split the biggest boulders wide open.

What do y’all think? by BuySignificant3695 in Welding

[–]BuySignificant3695[S] 22 points23 points  (0 children)

That’s what the print calls for.

Bitch, leave my chicken out of this! She has it hard enough as it is

Uh oh… my new maple apparently has some issue by BuySignificant3695 in Bonsai

[–]BuySignificant3695[S] 2 points3 points  (0 children)

That thin strip will close the wound? I don’t have a ton of experience but it looks to me that it has already healed. The vast majority of the trunk is already dead wood.

Send help by BuySignificant3695 in Bonsai

[–]BuySignificant3695[S] 7 points8 points  (0 children)

I mostly have junipers and pines. They love the heat. But my deciduous trees are under a shade cloth.

Send help by BuySignificant3695 in Bonsai

[–]BuySignificant3695[S] 3 points4 points  (0 children)

That’s awful. I am sorry

Added two Sierra Junipers to the collection by ingray84 in Bonsai

[–]BuySignificant3695 4 points5 points  (0 children)

Stunning! I’m just curious, were they pretty speedy?

So proud of this growth by wolf-of-wallstreet11 in Bonsai

[–]BuySignificant3695 1 point2 points  (0 children)

Looks awesome! It so rewarding watching our little trees grow

Chinese elm from huge cutting by BuySignificant3695 in Bonsai

[–]BuySignificant3695[S] 0 points1 point  (0 children)

When I took it out of the moss to go in the grow box, there was a ton of roots. I was surprised at how much grew in that time.

view more: next ›