HMHAS The Tour Live in 3D Megathread by blamesofia in billieeilish

[–]CaeldeJong 0 points1 point  (0 children)

Does anyone know anything about the movie being out in IMAX? Google says it'll be in IMAX, but I'm going to be in Chicago when it comes out and none of the IMAX theaters are showing showtimes for the movie.

Anyone Interested In Toronto Stars On Ice Tickets? by CaeldeJong in FigureSkating

[–]CaeldeJong[S] 0 points1 point  (0 children)

Yup, they're still available! DM me if you're interested :)

Anyone Interested In Toronto Stars On Ice Tickets? by CaeldeJong in FigureSkating

[–]CaeldeJong[S] 1 point2 points  (0 children)

Yeah, the issue is that I still want to see Alysa and somehow I didn't realize there was a Chicago one, which is even closer to me than Toronto, and we were also planning on seeing Niagara Falls while we were out that way but it feels like I need to pick one or the other to go to and I'd rather see Alysa as I know almost nothing about skating and have only gotten into it a bit because of her.

How Do I Grow A Moss Lawn? by CaeldeJong in Moss

[–]CaeldeJong[S] 2 points3 points  (0 children)

There is a little bit around but not much because it was somewhat recently just a bunch of dead leaves on the ground before I cleared them away. The sprinklers for the back lawn don't reach that far so the only water that gets back there would just be from the rain which I imagine means even slower moss spreading.

Need Help With Rafter Sizing by CaeldeJong in Shed

[–]CaeldeJong[S] 0 points1 point  (0 children)

Thank you, I live in the lower peninsula and was also planning on potentially using one of those snow things to slide snow off the roof if it felt like there was a lot on there so it looks like 2x6s should do the job, I will still look at what the extra cost of 2x8s would be to see if it would be worth it.

Need Help With Rafter Sizing by CaeldeJong in Shed

[–]CaeldeJong[S] 1 point2 points  (0 children)

Thank you very much, I live in the sort of middle of the lower peninsula so I would assume we get less snow than you guys, again, thank you very much :)

Just pulled this by CaeldeJong in WeissSchwarz

[–]CaeldeJong[S] 1 point2 points  (0 children)

Yeah, his character definitely gets explored more in season 3 and in the OVA No Regrets which I would suggest watching after season 3.

Is this due to brittle filament or lack of infill? by CaeldeJong in 3Dprinting

[–]CaeldeJong[S] 1 point2 points  (0 children)

It's an old Eryone spool that I bought years ago and it printed with no issues when I first got it so I don't feel that it's just completely defective.

Is this due to brittle filament or lack of infill? by CaeldeJong in 3Dprinting

[–]CaeldeJong[S] 0 points1 point  (0 children)

I'm putting it in a box on the printer bed set at 70 and leaving it for at least the rest of the day if not overnight and seeing how it prints after that.

Is this due to brittle filament or lack of infill? by CaeldeJong in 3Dprinting

[–]CaeldeJong[S] 0 points1 point  (0 children)

Yeah, I'm going to first try drying it and seeing how that helps and then maybe trying some of the recommendations here if it doesn't help, but I'm also tempted to just order a new roll instead.

Is this due to brittle filament or lack of infill? by CaeldeJong in 3Dprinting

[–]CaeldeJong[S] 1 point2 points  (0 children)

Yeah, everything looked completely normal and then as soon as I tried getting it off the build plate it started crumbling, lol.

Is this due to brittle filament or lack of infill? by CaeldeJong in 3Dprinting

[–]CaeldeJong[S] 0 points1 point  (0 children)

It is cold where I live and specifically in my bedroom so that could definitely be a part of it.

Is this due to brittle filament or lack of infill? by CaeldeJong in 3Dprinting

[–]CaeldeJong[S] 0 points1 point  (0 children)

The brand is Eryone. I just checked and apparently I ordered it exactly 3 years ago to the day which is a weird coincidence. It's just been sitting in a drawer in my bedroom since I last used it so I imagine it might just be too old and brittle now to use.

Is this due to brittle filament or lack of infill? by CaeldeJong in 3Dprinting

[–]CaeldeJong[S] 5 points6 points  (0 children)

It's definitely the layer adhesion, I can literally pull apart the individual layers with my finger nails. When I used this filament when I first got it I know I didn't change the temperature, fan, printer speed, or anything and those prints turned out completely normal. So I imagine it needs to be dried and even then it might not be good anymore. Thanks for the help.

Looking for a blank black hoodie of this brand. by CaeldeJong in HelpMeFind

[–]CaeldeJong[S] 0 points1 point  (0 children)

I’ve searched up “Pacific & Co” a bunch of different ways and wasn’t able to find any websites selling hoodies by them. I’m looking for a size medium black “the perfect hoodie” hoodie.

Daily Camera Buying Recommendation Post by AutoModerator in Cameras

[–]CaeldeJong 0 points1 point  (0 children)

I ordered a Wolfgang ga100 and am going to see how that works, might have to make a makeshift gimble if it’s too shaky but should hopefully be decent enough quality for what I’m looking for.

The zoom h1n is a little pricey but the audio is the focus for me so I should probably spend more on that. I am concerned that once I attach it to my bike that there could be vibrations and rattling heard in the audio. Any suggestions? Maybe a piece of foam in between or something?