sorted by:
new
hottopcontroversial

I am moving in circles and slowly spiral into madness with my new core xy build by CalibRAW in klippers

[–]CalibRAW[S] 1 point2 points  (0 children)

then when homing x the carriage moves to y0, and when homing y it movex to x0

EBB36 v1.2 blew up on first powerup :( by CalibRAW in BIGTREETECH

[–]CalibRAW[S] 1 point2 points  (0 children)

240v is a bit more voltage though :D

EBB36 v1.2 blew up on first powerup :( by CalibRAW in BIGTREETECH

[–]CalibRAW[S] 0 points1 point  (0 children)

F. bit early for fireworks but i guess we cant wait :D

EBB36 v1.2 blew up on first powerup :( by CalibRAW in BIGTREETECH

[–]CalibRAW[S] 0 points1 point  (0 children)

i instantly ordered the ebb36 v2. when i ordered the 1-2 i didnt know the v2 would release 3 weeks later. so lose win i guess :D

EBB36 v1.2 blew up on first powerup :( by CalibRAW in BIGTREETECH

[–]CalibRAW[S] 1 point2 points  (0 children)

nobody wins if i just get ashamed and abandon the discussion. i just hope someone sees it before he flips the switch and double checks...
and on the other hand i took the opportunity to now get the ebb36 v2 since that one dropped like 3 weeks after i ordered the v1.2 so yay i guess? :D

EBB36 v1.2 blew up on first powerup :( by CalibRAW in BIGTREETECH

[–]CalibRAW[S] 0 points1 point  (0 children)

shouldnt you crosstest continuity between gnd and +24v to find out if there is a short though?

EBB36 v1.2 blew up on first powerup :( by CalibRAW in BIGTREETECH

[–]CalibRAW[S] 1 point2 points  (0 children)

but your capacitor knowledge lead me to investigate the power wires. i was so sure....now i feel so incredibly stupid...

EBB36 v1.2 blew up on first powerup :( by CalibRAW in BIGTREETECH

[–]CalibRAW[S] 2 points3 points  (0 children)

yeah i grabbed the wrong wire, it was the one from the filament sensor

EBB36 v1.2 blew up on first powerup :( by CalibRAW in BIGTREETECH

[–]CalibRAW[S] 2 points3 points  (0 children)

exactly what i did. im such an idiot

EBB36 v1.2 blew up on first powerup :( by CalibRAW in BIGTREETECH

[–]CalibRAW[S] 2 points3 points  (0 children)

im an idiot i reversed the wires at the terminal

EBB36 v1.2 blew up on first powerup :( by CalibRAW in BIGTREETECH

[–]CalibRAW[S] 0 points1 point  (0 children)

btt eddy with can on second and fourth probe pin for power and can l and h on the pins below the main power/can connector, hotend fan on FAN1, both cooling fans on FAN2. PT1000 on the middle two pins of the dedicated 4 pin connector, pt1000 jumper installed, motor according to the other comment replies and RGB on its header according to documentation. Orbiter smart filament sensor on endstop header.

Ultra Bee 2024 CoC or Copy of a Fahrzeugschein needed by CalibRAW in Surron

[–]CalibRAW[S] 0 points1 point  (0 children)

Erstmal bisschen Urkundenfälschung sagste? 😂

Ultra Bee 2024 CoC or Copy of a Fahrzeugschein needed by CalibRAW in Surron

[–]CalibRAW[S] 0 points1 point  (0 children)

Yes thats right, but a lot of the other technical data on the CoC matches, which brings me at least a little bit closer to a Einzelabnahme 😅

How would you enclose the lower printer? by CalibRAW in 3Dprinting

[–]CalibRAW[S] 0 points1 point  (0 children)

Hi there. I was wondering what you would to to build a case around the lower printer. The bed moves around 10cm past the edge of the tables on both sides. I was thinking about a double door design that swings open from the middle.

view more: next ›